background image

     

iii

DynoWare RT Upgrade for Model 424x Dynamometers Installation Guide

W

ARNINGS

Disclaimers

Dynojet Research, Inc. (Dynojet) makes no representation or warranties with respect to the contents 

hereof and specifically disclaims any implied warranties of merchantability for any particular purpose.
Dynojet reserves the right to revise this publication and to make changes from time to time in the 

content hereof without obligation of Dynojet to notify any person of such revision or changes.
Dynojet is not responsible for false operation due to unexpected dynamometer operation such as may 

be caused by static, software bugs, hardware failure, etc.
Dynojet is not responsible for damage resulting from improper installation of the dynamometer or 

from improper service rendered to the dynamometer. Dynojet is not responsible for damage incurred 

due to alteration of the dynamometer or components, use of unapproved parts, or abuse to the 

dynamometer.
Do not connect or disconnect cables or components on the dynamometer with the power on.
Always wear protective clothing, ear protection, and eye protection (goggles, safety glasses) when using 

and servicing the dynamometer. 

CAUTION

Equipment Power Requirements

The dynamometer has specific power requirements. Connecting the dynamometer to the incorrect 

voltage will void the dynamometer warranty. Installation may require a licensed electrician.

Potentially Lethal Voltages

Components attached to and within the dynamometer operate with potentially lethal voltages. To 

provide the greatest assurance of safety, the AC power cord(s) must be disconnected from the power 

source before servicing electrical components or wiring. Disconnect all power cords before servicing 

electrical components for the greatest assurance of safety.

Summary of Contents for Dynoware RT

























































































Reviews: