ENGLISH 10-1123
Troubleshooting
1 The power LED is not lit
Make sure that the power adapter is connected correctly and the
power outlet is supplying power.
2 The link/act LED is not lit when a device is connected to the
corresponding port
Make sure that the cables are connected correctly and securely to
the switch and device. Make sure that the cable is not longer than
328 ft. (100 m).
Specifications
Standards
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab,
IEEE
802.1p
Topology
Star
Protocol
CSMA/CD
Data transfer rate
Ethernet: 10 Mbps (Half Duplex),
20 Mbps (Full Duplex)
Fast Ethernet: 100 Mbps (Half Duplex),
200 Mbps (Full Duplex)
Gigabit Ethernet: 2000 Mbps (Full Duplex)
Network media (cable)
10Base-T: UTP category 3, 4, 5 cable
(maximum
100
m)
EIA/TIA-568 100Ω STP (maximum 100 m)
100Base-TX: UTP category 5, 5e cable
(maximum
100
m)
EIA/TIA-568 100Ω STP (maximum 100 m)
1000Base-TX: UTP category 5e, 6 cable
(maximum
100
m)
EIA/TIA-568 100Ω STP (maximum 100 m)
Number of ports
Five 10/100/1000M RJ45 ports
LED indicators
Power,
Link/Act
Transfer method
Store-and-Forward
MAC address learning
Automatic learning and aging
Frame filter rate
10Base-T: 14880 pps/Port
100Base-Tx:
148800
pps/Port
1000Base-T:
1488000
pps/Port
Frame forward rate
10Base-T: 14880 pps/Port
100Base-Tx:
148800
pps/Port
1000Base-T:
1488000
pps/Port
Operating temperature
32°F~104°F
(0°C~40°C)
Storage temperature
-40°F~158°F
(-40°C~70°C)
Operating humidity
10%~90%
non-condensing
Storage humidity
5%~90%
non-condensing
Legal notices
FCC statement
This equipment complies with Part 15 of the FCC Rules. Operation is
subject to the following conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note
: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
more or the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
One-Year Limited Warranty
Visit www.dynexproducts.com for details.
Contact Dynex
For customer service please call 800-305-2204
www.dynexproducts.com
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
© 2010 BBY Solutions, Inc. All Rights Reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All
other products and brand names are trademarks of their respective owners.
DX-GB5PRT_10-1123_QSG_V1.eps 2 10/29/2010 10:16:13 AM
DX-GB5PRT_10-1123_QSG_V1.eps 2 10/29/2010 10:16:13 AM
