Dynex DX-LDVD19-10A - 19" LCD TV, Service Manual

Page: 19 / 57

Connecting an antenna or cable TV
To connect an antenna, cable TV, or satellite TV box:
1 Connect one end of a 75 ohm cable (not included) to the RF OUT
jack on the antenna or on the cable or satellite TV box.
2 Connect the other end of the cable to the ANT/CABLE IN jack on
the back of your TV.
Notes:
Use a 75 ohm cable to eliminate interference and noise from radio waves.
Do not bundle the 75 ohm cable with the power cord or other cables.
If the antenna is not installed correctly, contact qualified service personnel
to correct the problem.
To improve picture quality in a poor signal area, purchase and install a
signal amplifier.
Connecting a cable TV or satellite box
If you subscribe to a cable TV service from a local provider you can watch
cable TV programming. The TV cannot display TV programming unless a
TV tuner device or cable TV converter box is connected to the TV.
For further information regarding cable TV service, contact your local
cable TV service provider(s).
To connect to a cable TV or satellite TV box:
1 Connect the incoming cable from the satellite wall jack to the
SATELLITE IN jack on the satellite box.
2 Depending on the jacks available on the satellite TV receiver (set
top box), connect a cable from the outgoing jacks on the satellite
box to the corresponding jacks on the back of your TV. The
connection can be to the HDMI, component video, S-Video, or AV
jack.
3 If you use a component video, S-Video, or AV cable, connect audio
cables to the corresponding jacks on the back of your TV and on
the staellite box.
4 Turn on your TV, then press INPUT to select VIDEO mode for the
type of connection you use.
5 Select the channel you want with the remote control for the
cable box.
Connecting a VCR
To connect a VCR (option 1):
1 Make sure that your TV’s power cord is unplugged and the VCR is
turned off.
2 Connect a 75 ohm RF wire to the ANT OUT jack on your VCR and
to the ANT/CABLE IN jack on your TV (1), then switch the output
of the VCR to 3 or 4 and tune your TV to the same channel.
To connect a VCR (option 2):
1 Make sure that your TV’s power cord is unplugged and the VCR is
turned off.
2 Connect an AV cable to the AV VIDEO OUT jack on the VCR.
3 Connect the other end of the cable to the VIDEO IN jack on the
back of your TV.
VHF antenna
UHF antenna
ANT/CABLE IN
Multi-family dwellings or apartments
Connect to wall antenna outlet.
Bronze wire - do not bend
Wall antenna outlet
75 ohm RF coaxial wire
Single-family dwellings or houses
Connect to wall antenna jack for
outdoor antenna.
Turn clockwise to tighten
Bronze wire - do not bend
&2
0
3
2
1
(
1
7
,
1
$8
'
,2
,1
5
/
9,
'
(2
,
1
<
3E
3U
6
9
,'
(
2
,1
$
8',
2
,1
/
5
+'
0
,
Back of TV
S-
V
id
e
o
c
a
bl
e
Co
m
p
o
n
en
t vi
deo
c
a
b
les
HD
M
I c
a
bl
e
Cable box
CO
M
PONENT
IN
A
UD
IO
IN
R
L
V
ID
E
OI
N
Y
Pb
P
r
S-
V
ID
EO
IN
A
UD
IO
IN
L
R
AN
T
/C
ABLE
IN
VCR
1
2
Back of TV
To S-VIDEO IN jack
To VIDEO IN and
AUDIO-L and R jacks
S-
Vi
d
e
o c
a
b
le
75 ohm RF wire
Note : Cables are often
color-coded to connectors.
Connect yellow to yellow,
red to red, and white to
white.
Vi
d
e
o
c
a
b
le
AU
D
IO
-L
a
n
d
R
c
a
b
le
s