Dynasty Fireplaces EF42D Home Owner'S Installation Instructions & Operating Manual Download Page 2

 

2

IMPORTANT INSTRUCTIONS

 

 

When using electrical appliances basic precautions should always be followed to reduce the risk of fire

electrical shock and injury to persons including the following

 

CAUTION

- High temperature, keep electrical cords, drapery, and other furnishings at least 3 feet (0.9m) 

from the front of the heater and away from the side and rear. 
1.  Read all instructions before using this appliance. 
2.  Do not use outdoors. 
3.  This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 
supervision or instruction concerning use of the appliance by a person responsible for their safety. 

4.  Children should be supervised to ensure that they do not play with the appliance. 

5.  This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep 

combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 
3 feet (0.9m) from the front of the heater and keep them away from the sides and rear. 

6.  Extreme caution is necessary when any heater is used by or near children or invalids and 

whenever the heater is left operating unattended. 

7.  Unplug power cord before servicing or moving the heater. Always unplug heater when not in 

use. 

8.  Do not operate any heater with a damaged cord or after the heater malfunctions, has been 

dropped or damaged in any manner. Return heater to authorized service facility for examination, 
electrical or mechanical adjustment, or repair. 

9.  This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. 

Never locate heater where it may fall into a bathtub or other water container. 

10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. 

Arrange cord away from traffic area and where it will not be tripped over. 

11. To disconnect heater, turn controls to off, then remove plug from outlet. 
12. Connect to properly grounded outlets only. 
13. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it 

may cause an electric shock or fire or damage the heater. Do not block or tamper with the 
heater in any manner while it is in operation. 

14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft 

surfaces, like a bed, where openings may become blocked.     

15. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, 

paint, or flammable liquids are used or stored

16. Use this heater only as described in this manual. Any other use not recommended by the 

manufacturer may cause fire, electrical shock, or injury to persons. 

17. Where possible, avoid the use of extension cords because the extension cord may overheat 

and cause a risk of fire.   

18. This heater includes an overheat protection system that shuts off the heater when parts of the 

heater are getting excessively hot. If the heater shuts off, immediately turn the heater OFF and 
inspect for any objects, on or adjacent to the heater, which may cause high temperatures. DO 
NOT OPERATE THE HEATER UNTIL IT IS RESET. To reset the heater, turn it OFF, unplug it 
from the electrical outlet, and wait five to ten minutes for the unit to cool down before plugging it 
back in and turning the heater on. 

19. Make certain that the power source conforms to the electrical requirements of the heater. 
20. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place 

heater on soft surfaces, like a bed, where openings may become blocked. 

21. A heater has hot and arcing or sparking parts inside. It must NOT be used in potentially 

dangerous locations such as flammable, explosive, chemical-laden or wet atmosphere. This 
heater is intended for use in general use only. 

WARNING: DO NOT DEPEND ON THE ON/OFF SWITCH THE SOLE MEANS OF 
DISCONNECTING POWER WHEN SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG 
THE POWER CORD.

 

WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK---DO NOT USE THIS 
HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES. 

22. SAVE THESE INSTRUCTIONS.

 

Summary of Contents for EF42D









Reviews: