Dynamite Passport UltraDuo DYN4300 Instruction Manual Download

Page: 2 / 4

NI-MH BATTERIES

NI-Cd CHARGING

LI-PO fAST CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT LiPo BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the LiPo FAST CHG screen and set charging param-

eters. The charging amperage

(A)

can be set between 0.1 and 10.0A. Voltage

(B)

is dependent on the number of cells in series. For example, with Li-Po batteries
these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
Near the end of a standard charging cycle, the charger switches from Constant
Current (CC) mode to Constant Voltage (CV) mode to slowly “top off” the current in
the battery as close as possible to the maximum capacity.
In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging
time; however, the final capacity of the battery will be less than what you would get
using the standard charge method.

LiPo FAST CHG

4.0A 7.4V(2S)

To select values other than the existing parameters:
• Press the

Jog dial

so the charge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the charge current value

• Press the

Jog dial

to save the value and the voltage value

(B)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the voltage (and # of cells in

series

(C)

)

• Press the

Jog dial

again to save the voltage value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, BALANCE, STORAGE or DISCHARGE.
To start charging, press and hold the

Jog dial

for 3 seconds.

LI-PO STORAGE CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT LiPo BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the LiPo STORAGE screen and set charging param-

eters. The charging amperage

(A)

can be set between 0.1 and 10.0A. Voltage

(B)

is dependent on the number of cells in series. For example, with Li-Po batteries
these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
If you don’t plan on using your battery for a long time, it is best to charge (or
discharge) the battery to its optimal storage voltage and capacity.

LiPo STORAGE

2.5A 11.1V(3S)

To select values other than the existing parameters:
• Press the

Jog dial

so the charge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the charge current value

• Press the

Jog dial

to save the value and the voltage value

(B)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the voltage (and # of cells in

series

(C)

)

• Press the

Jog dial

to save the voltage value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, BALANCE, FAST CHG or DISCHARGE.
To start charging, press and hold the

Jog dial

for 3 seconds.

LI-PO dISCHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT LiPo BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the LiPo DISCHARGE screen and set discharging

parameters. The discharging amperage

(A)

can be set between 0.1 and 5.0A. Volt-

age

(B)

is dependent on the number of cells in series. For example, with Li-Po bat-

teries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries).
A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged.

LiPo DISCHARGE

2.0A 22.2V(6S)

To select values other than the existing parameters:
• Press

Jog dial

so the discharge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the discharge current value

• Press the

Jog dial

to save the value and the voltage value

(B)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the voltage (and # of cells in

series

(C)

)

• Press

Jog dial

to save the voltage value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, BALANCE, FAST CHG or STORAGE.
To start discharging, press and hold the

Jog dial

for 3 seconds.

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiMH BATT screen. Press the

Jog dial

to select

NiMH.
Rotate the

Jog dial

to go to one of the control screens (CHARGE, Auto CHARGE,

DISCHARGE, RE-PEAK or CYCLE) to do what your battery needs.
Correctly connect your Ni-MH battery to the charger. Press the

Jog dial

and adjust

the charging parameters as needed. Press and hold the

Jog dial

(approximately 3

seconds) until the screen changes to start the battery check/charge sequence.
After confirmation, charging starts and information will show on the LCD screen
(information may vary).

NiMH 2.0A 7.59V

CHG 022:43

01082

A Ni-MH battery pack is
charging

Charging rate is 2.0A
(2000mAh)

Voltage being applied to the battery is currently 7.59V

Present charge level of the battery is 1082 mAh

Time elapsed since the charge process started is 22:43

During charging, the

Jog dial

can be rotated counterclockwise to show several

parameter messages on the LCD screen, including: Ni-MH Sensitivity, Input Power
Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status
and Capacity Cutoff. The charger signals when the charging (or discharging)
process is complete (if Buzzer is set to ON).

CAUTION:

The Ni-MH program menus are to be used ONLY for the

charging and discharging of Ni-MH battery packs. The charging of other
battery types using these programs will result in damage to the battery
or charger.

CAUTION:

Using a charge rate that is not compatible with the battery

capacities may result in damage or malfunction of the charger or
batteries.

NI-MH CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiMH BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiMH CHARGE screen and set charging param-

eters. The charging amperage

(A)

can be set between 0.1 and 10.0A.

NiMH CHARGE

CURRENT 1.0A

To select a value other than the existing parameter:
• Press the

Jog dial

so the charge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the charge current value

• Press the

Jog dial

to save the value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE.
To start charging, press and hold the

Jog dial

for 3 seconds.

NI-MH AUTO CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiMH BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiMH Auto CHARGE screen and set charging

parameters. The charging amperage

(A)

can be set between 0.1 and 10.0A.

NiMH Auto CHARGE

CURRENT 1.0A

To select a value other than the existing parameter:
• Press the

Jog dial

so the charge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the charge current value

• Press the

Jog dial

to save the value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, DISCHARGE, RE-PEAK or CYCLE.
To start charging, press and hold the

Jog dial

for 3 seconds.

NI-MH dISCHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiMH BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiMH DISCHARGE screen and set discharging

parameters. The discharging amperage

(A)

can be set between 0.1 and 5.0A.

A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged. The discharge level can be
set from 0.1 to 25.2V.

NiMH DISCHARGE

0.1A

CUT: 1.0V

To select a value other than the existing parameter:
• Press the

Jog dial

so the discharge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the discharge current value

• Press the

Jog dial

to save the value and the cutoff voltage value

(B)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the cutoff voltage

• Press the

Jog dial

to save the voltage value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, Auto CHARGE, RE-PEAK or CYCLE.
To start discharging, press and hold the

Jog dial

for 3 seconds

NI-MH RE-PEAK CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiMH BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiMH RE-PEAK screen and set re-peak param-

eters to a value of between 1 and 3.

NiMH RE-PEAK

To select a value other than the existing parameter:
• Press the

Jog dial

so the re-peak value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the value

• Press the

Jog dial

to save the value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, Auto CHARGE, DISCHARGE or CYCLE.
Press the

Jog dial

to go to the next menu.

NI-MH CyCLE CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiMH BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiMH CYCLE screen and set charge/discharge

cycle count parameters.
The battery can be put through a series of charge/discharge cycles using this
program. Cycling Ni-MH batteries can increase capacity and rejuvenate neglected
batteries. Discharge capacity and average battery voltage help you compare batter-
ies for the best run time and power.

NiMH CYCLE

CHG>DCHG 5

To select values other than the existing parameter:
• Press the

Jog dial

so the cycle type

(A)

flashes

• Rotate the

Jog dial

to set the cycle type as CHG>DCHG or DCHG>CHG

• Press the

Jog dial

to save your choice and the number of cycles

(B)

flashes

• Rotate the

Jog dial

to set the cycle count between 1 to 5

• Press the

Jog dial

to save the cycle count value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, Auto CHARGE, DISCHARGE or RE-PEAK.
To start cycling, press and hold the

Jog dial

for 3 seconds.

NI-Cd BATTERIES

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiCd BATT screen. Press the

Jog dial

to select

NiCd.
Rotate the

Jog dial

to go to one of the control screens (CHARGE, Auto CHARGE,

DISCHARGE, RE-PEAK or CYCLE) to do what your battery needs.
Correctly connect your Ni-Cd battery to the charger. Press the

Jog dial

and adjust

the charging parameters as needed. Press and hold the

Jog dial

(approximately 3

seconds) until the screen changes to start the battery check/charge sequence.
After confirmation, charging starts and information will show on the LCD screen
(information may vary).

NiCd 2.0A 7.59V

CHG 022:43

01082

A Ni-Cd battery pack is
charging

Charging rate is 2.0A
(2000mAh)

Voltage being applied to the battery is currently 7.59V

Present charge level of the battery is 1082 mAh

Time elapsed since the charge process started is 22:43

During charging, the

Jog dial

can be rotated counterclockwise to show several

parameter messages on the LCD screen, including: Ni-Cd Sensitivity, Input Power
Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status
and Capacity Cutoff. The charger signals when the charging (or discharging)
process is complete (if Buzzer is set to ON).

CAUTION:

The Ni-Cd program menus are to be used ONLY for the

charging and discharging of Ni-Cd battery packs. The charging of other
battery types using these programs will result in damage to the battery
or charger.

CAUTION:

Using a charge rate that is not compatible with the battery

capacities may result in damage or malfunction of the charger or
batteries.

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiCd BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiCd CHARGE screen and set charging param-

eters. The charging amperage

(A)

can be set between 0.1 and 10.0A.

NiCd CHARGE

CURRENT 1.0A

To select a value other than the existing parameter:
• Press the

Jog dial

so the charge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the charge current value

• Press the

Jog dial

to save the value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE.
To start charging, press and hold the

Jog dial

for 3 seconds.

NI-Cd AUTO CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiCd BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiCd Auto CHARGE screen and set charging

parameters. The charging amperage

(A)

can be set between 0.1 and 10.0A.

NiCd Auto CHARGE

CURRENT 1.0A

To select a value other than the existing parameter:
• Press the

Jog dial

so the charge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the charge current value

• Press the

Jog dial

to save the value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, DISCHARGE, RE-PEAK or CYCLE.
To start charging, press and hold the

Jog dial

for 3 seconds.

NI-Cd dISCHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiCd BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiCd DISCHARGE screen and set discharging

parameters. The discharging amperage

(A)

can be set between 0.1 and 5.0A.

A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged. The discharge level can be
set from 0.1 to 25.2V.

NiCd DISCHARGE

0.1A

CUT: 1.0V

To select a value other than the existing parameter:
• Press the

Jog dial

so the discharge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the discharge current value

• Press the

Jog dial

to save the value and the cutoff voltage value

(B)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the cutoff voltage

• Press the

Jog dial

to save the voltage value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, Auto CHARGE, RE-PEAK or CYCLE.
To start discharging, press and hold the

Jog dial

for 3 seconds

NI-Cd RE-PEAK CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiCd BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiCd RE-PEAK screen and set re-peak parameters

to a value of between 1 and 3.

NiCd RE-PEAK

To select a value other than the existing parameter:
• Press the

Jog dial

so the re-peak value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the value

• Press the

Jog dial

to save the value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, Auto CHARGE, DISCHARGE or CYCLE.
Press the

Jog dial

to go to the next menu.

NI-Cd CyCLE CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT NiCd BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the NiCd CYCLE screen and set charge/discharge

cycle count parameters.
The battery can be put through a series of charge/discharge cycles using this
program. Cycling Ni-Cd batteries can increase capacity and rejuvenate neglected
batteries. Discharge capacity and average battery voltage help you compare batter-
ies for the best run time and power.

NiCd CYCLE

CHG>DCHG 5

To select values other than the existing parameter:
• Press the

Jog dial

so the cycle type

(A)

flashes

• Rotate the

Jog dial

to set the cycle type as CHG>DCHG or DCHG>CHG

• Press the

Jog dial

to save your choice and the number of cycles

(B)

flashes

• Rotate the

Jog dial

to set the cycle count between 1 to 5

• Press the

Jog dial

to save the cycle count value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE, Auto CHARGE, DISCHARGE or RE-PEAK.
To start cycling, press and hold the

Jog dial

for 3 seconds.

PB BATTERIES

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT Pb BATT screen. Press the

Jog dial

to select Pb.

Rotate the

Jog dial

to go to one of the control screens (CHARGE or DISCHARGE)

to do what your battery needs.
The nature of a Lead Acid or Sealed Lead Acid battery is very different from that of
Lithium, Ni-MH or Ni-Cd batteries. The output current of a Pb battery is lower than
other batteries relative to their capacities. Furthermore, lead acid batteries can’t be
charged at a level greater than 1/10 their capacity.
For example, a 5000mAh lead acid battery can’t be charged at a rate greater than
0.5A. For more details on the charge and discharge capabilities of your battery,
please refer to the charging data supplied by the battery manufacturer.
Correctly connect your Pb battery to the charger. Press the

Jog dial

and adjust

the charging parameters as needed. Press and hold the

Jog dial

(approximately 3

seconds) until the screen changes to start the battery check/charge sequence.
After confirmation, charging starts and information will show on the LCD screen
(information may vary).

Pb-6 0.4A 12.39V

CHG 022:43

01082

A Lead Acid battery pack is

charging

Battery pack has 6 cells

in series

Charging at a rate of 0.4A (400mAh)

Voltage being applied to the battery is currently 12.39V

Present charge level of the battery is 1082mAh

Time elapsed since the charge process started is 22:43

During charging, the

Jog dial

can be rotated counterclockwise to show several

parameter messages on the LCD screen, including: End Voltage, Capacity Cutoff,
Safety Timer Status, Temperature Cutoff and Input Power Voltage. The charger
signals when the charging (or discharging) process is complete (if Buzzer is set to
ON).

CAUTION:

The Pb program menus are to be used ONLY for the charging

and discharging of Pb battery packs. The charging of other battery types
using these programs will result in damage to the battery or charger.

CAUTION:

Using a charge rate that is not compatible with the battery

capacities may result in damage or malfunction of the charger or
batteries.

PB CHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT Pb BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the Pb CHARGE screen and set charging parameters.

The charging amperage

(A)

can be set between 0.1 and 10.0A.

Pb CHARGE

0.1A

2.0V (1P)

To select values other than the existing parameters:
• Press the

Jog dial

so the charge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the charge current value

• Press the

Jog dial

to save the charge current value and the battery voltage

value

(B)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the battery voltage/cell count

value (Pb batteries are 2.0V per cell, for a 6 cell battery this would be 2.0V x 6
cell = 12.0V)

• Press the

Jog dial

to save the voltage

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as DISCHARGE.
To start charging, press and hold the

Jog dial

for 3 seconds.

PB dISCHARGING

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT Pb BATT screen. Press the

Jog dial

to go into

this menu.
Rotate the

Jog dial

to go to the Pb DISCHARGE screen and set discharging

parameters. The discharging amperage

(A)

can be set between 0.1 and 5.0A.

A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged. The discharge level can be
set from 2 to 20V.

Pb DISCHARGE

0.1A

2.0V (1P)

To select values other than the existing parameters:
• Press the

Jog dial

so the discharge current value

(A)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the discharge current value

• Press the

Jog dial

to save the value and the cutoff voltage value

(B)

flashes

• Rotate the

Jog dial

to INCREASE OR DECREASE the cutoff voltage

• Press the

Jog dial

to save the voltage value

If no parameters are flashing, you can rotate the

Jog dial

to select another

program such as CHARGE.
To start discharging, press and hold the

Jog dial

for 3 seconds

BATTERy MEMORy

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT BATT MEMORY screen. Press the

Jog dial

select BATT MEMORY.
Use this menu to create a battery profile. To reduce the time required to initiate a
charging or discharging cycle on a battery you regularly use, this charger has been
designed with the capability of storing up to 10 battery profiles that can be quickly
accessed and run at a later time.
• Rotate the

Jog dial

to identify a battery profile, 1 through 10

• Press the

Jog dial

to select battery profile 1

• Press the

Jog dial

so battery type flashes

• Rotate the

Jog dial

to select a battery type

• Press the

Jog dial

to save the battery type

Follow this process using the

Jog dial

to select, change, then save each param-

eter (battery voltage, charge current, discharge current, discharge voltage, Terminal
Voltage Control (TVC) and temperature cutoff). Then save the battery profile.

• Rotate the

Jog dial

to select SAVE PROGRAM

• Press the

Jog dial

to save the program

• Repeat this process to enter additional battery profiles
• Press the

Mode key

until you reach the 9 main menus

CAUTION:

Increasing the TVC value beyond the default settings may result in a

shorter battery life and/or damage to the battery. Do not change the TVC value

unless you fully understand the effects TVC will have on your battery.

To Charge or Discharge a battery using the saved profile:
Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT BATT MEMORY screen. Press the

Jog dial

select BATT MEMORY.
• Rotate the

Jog dial

to identify the battery profile, 1 through 10.

• Press and hold the

Jog dial

for 3 seconds

• Rotate the

Jog dial

to choose the type of charge function you wish to perform

• Press and hold the

Jog dial

for 3 seconds to start

SySTEM SET

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT SYSTEM SET screen. Press the

Jog dial

to select

SYSTEM SET.
Use this menu to set the “behind the scenes” operating parameters for this charger such as; Rest Time, Safety Timer, Capacity Cutoff, Key Beep/Buzzer, Input Power Low
Cutoff, External and Internal Temperatures, Load Factory Settings and Version.

LI BATTERy VOLTAGE CHECKER OPERATION - USING THE BALANCE AdAPTER PORT

The Passport™ Ultra Duo charger has the capability to read and display the indi-
vidual cell voltages of a Li-Po, Li-Fe or Li-Io battery. This voltage checking function
can only be used when the charger is powered ON and not charging a battery.
To use the voltage checker, connect the balance port connector of your Li-Po, Li-Fe
or Li-Io battery to the balance adapter board connected to the Balance Circuit
Adapter Board Connector

(C)

Press the

Mode key

until you reach the 9 main menus, then rotate the

Jog dial

to locate the PROGRAM SELECT LI BATT METER screen. Press the

Jog dial

select LI BATT METER.
In a few moments, the charger will begin to display the cell voltages of the battery
in the following format:

3.70 3.70 0.00 V

0.00 0.00 0.00 V

This example is for a 2S battery, so only the voltages for these two cells are
displayed. The data is presented in this format:

1–1 1–2 1–3 V

1–4 1-5 1–6 V

At this point, you can rotate the

Jog dial

to see a display of the overall battery

voltage as well as the individual high- and low-cell voltage values.

MAIN 08.20V

H4.104V L4098V

You may exit this menu at any time by pressing the

Mode key

to return to the

main menus.

USB ACCESSORy CHARGER OPERATION (COMPATIBLE WITH iPhone ANd iPod dEVICES)

The Passport Ultra Duo charger has the capability to charge your iPhone, iPod or USB compatible device with the 1A USB charge port (E). To use the charging function,
simply connect a compatible charging device or cord into the charge port while the charger is powered ON. The internal USB charge port will provide up to 1A current at
5V DC.

REST TIME

Use this menu to set the Rest time during each step in a cycle.When a Ni-MH
or Ni-CD battery is cycled (charged, discharged and charged again) it will get
hot, therefore it is necessary to set a rest time interval during each step of the
process to make sure the battery and charger are completely cooled before
moving on to the next part of the cycle. Default time is 10 minutes, but this
can be set between 1 and 60 minutes. To select a value other than the default
parameter:
• Press the

Jog dial

to select Rest Time

• Press the

Jog dial

so the Rest Time value flashes

• Rotate the

Jog dial

to select Rest Time in Minutes

• Press the

Jog dial

to save the Rest Time value

• Rotate the

Jog dial

to select SAFETY TIMER

SAfETy TIMER

Use this menu to set a time limit for charging a battery. When a charge cycle
is started, a clock inside the charger will begin recording the elapsed charge
time. If the SAFETY TIMER function has been turned ON, the charger will stop
the charging process once this time limit has been reached to avoid damage
caused by over-charging the battery. This time value can be set between 1 and
720 minutes.
To select values other than the default parameters:
• Press the

Jog dial

so the ON/OFF value flashes

• Rotate the

Jog dial

to select ON or OFF

• Press the

Jog dial

to save the value

• Rotate the

Jog dial

to select the value for time

• Press the

Jog dial

to save the value

• Rotate the

Jog dial

to select Capacity Cutoff

CAPACITy CUTOff

Use this menu to set a capacity limit at which the charger will stop charging a
battery. When a charge cycle starts, the charger records the battery capacity.
When the Capacity Cutoff function is set at ON, the charger will stop charging at
the capacity limit to prevent battery damage. Capacity can be adjusted between
100 and 50,000mAh.
• Press the

Jog dial

so the ON/OFF value flashes

• Rotate the

Jog dial

to select ON or OFF

• Press the

Jog dial

to save the value

• Rotate the

Jog dial

to select the Capacity Cutoff value

• Press the

Jog dial

to save the value

• Rotate the

Jog dial

to select Key Beep/Buzzer

KEy BEEP/BUZZER

Use this menu to set the key beep and charger alarm buzzer at ON or OFF as
needed. We recommend that you keep the alarm ON so the alarm will sound
when charging is complete or if there is cause for alarm during charging.
To select values other than the default parameters:
• Press the

Jog dial

so the Key Beep ON/OFF value flashes

• Rotate the

Jog dial

to select ON or OFF

• Press the

Jog dial

to save the value

• Press the

Jog dial

so the Buzzer ON/OFF value flashes

• Rotate the

Jog dial

to select ON or OFF

• Press the

Jog dial

to save the value

• Rotate the

Jog dial

to select Input Power Low Cutoff

INPUT POWER LOW CUTOff

Use this menu to set the input voltage limit so an alarm will sound if the voltage
goes below the cutoff value. The voltage alarm value can be set anywhere from
10.0 to 11.0V.
To select a value other than the default parameter:
• Press the

Jog dial

so the voltage value flashes

• Rotate the

Jog dial

to select the voltage value

• Press the

Jog dial

to save the value

• Rotate the

Jog dial

to select External and Internal Temperatures

EXTERNAL ANd INTERNAL TEMPERATURES

By selecting the External and Internal Temperatures Screen you can view the
current temperatures of both the battery (external) and the charger (internal).
The optional temperature sensor (DYN5033) is required for external temperature
measurement.

RESET fACTORy SETTINGS

• Press the

Jog dial

to reset the charger to factory settings

• Press the

Jog dial

to select VERSION

VERSION

By selecting the Version Screen you can view the version (revision number) of the
software on your charger.

TROUBLESHOOTING GUIdE

LCD Screen Warning and Error messages shown below.
During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger’s LCD screen, make the recommended responses.
If the message continues after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance.

REVERSE POLARITY

Make sure each connection polarity is correct between the power source and the charger, then between the charger and the battery

CONNECTION BREAK

Make sure the power connections are correct for charging

SHORT ERR

Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires.

INPUT VOL ERR

Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger provides correct
input voltage.

VOL SELECT ERR

Incorrect setting for cell in series count (pack voltage) of a lithium battery. Make charger settings match the battery pack label cell in series count
specifications or replace the battery.

BREAK DOWN

Charger electronics require repair.

BATTERY CHECK LOW VOLTAGE Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
BATTERY CHECK HIGH VOLTAGE Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.

Battery Type

Li-Po

Li-Io

Li-Fe

Ni-MH

Ni-Cd

Standard voltage (Volts per cell)

3.70

3.60

3.30

1.20

2.00

Max. voltage (Volts per cell)

4.20

4.10

3.60

1.60

2.45

Min. voltage (Volts per cell)

3.00

2.00

1.00

0.85

1.75

You may exit this menu at any time by pressing the

Mode key

to return to the main menus.

Summary of Contents for Passport UltraDuo DYN4300

Page 1: ...tery is 1082mAh F Time elapsed since the charge process started is 22 43 22 minutes and 43 seconds During charging the Jog Dial can be rotated counterclockwise to show several parameter messages on the LCD screen including End Voltage Input Power Volt age External Internal Temperature Temperature Cutoff Safety Timer Status and Capacity Cutoff Rotate the Jog Dial clockwise to show the charge voltag...

Page 2: ... peak value A flashes Rotate the Jog Dial to INCREASE OR DECREASE the value Press the Jog Dial to save the value If no parameters are flashing you can rotate the Jog Dial to select another program such as CHARGE Auto CHARGE DISCHARGE or CYCLE Press the Jog Dial to go to the next menu 31 Ni CD Cycle Charging Press the Mode key until you reach the 9 main menus then rotate the Jog Dial to locate the ...

Page 3: ...itraum entspricht den gesetzlichen Bestimmung des Landes in dem das Produkt erworben wurde In Deutschland beträgt der Garantiezeitraum 6 Monate und der Gewährleistungszeitraum 18 Monate nach dem Garantiezeitraum Einschränkungen der Garantie a Die Garantie wird nur dem Erstkäufer Käufer gewährt und kann nicht übertragen werden Der Anspruch des Käufers besteht in der Reparatur oder dem Tausch im Rah...

Page 4: ...agères Durata della Garanzia Periodo di garanzia Garanzia esclusiva Horizon Hobby Inc Horizon garantisce che i prodotti acquistati il Prodotto sono privi di difetti relativi ai materiali e di eventuali errori di montaggio Il periodo di garanzia è conforme alle disposizioni legali del paese nel quale il prodotto è stato acquistato Tale periodo di garanzia am monta a 6 mesi e si estende ad altri 18 ...

Search results

Summary of Contents for Passport UltraDuo DYN4300

Reviews:

Related manuals for Passport UltraDuo DYN4300

Brands by name

Popular brands

Dynamite Passport UltraDuo DYN4300, Instruction Manual

Search results

Summary of Contents for Passport UltraDuo DYN4300

Reviews:

Related manuals for Passport UltraDuo DYN4300

Brands by name

Popular brands