Dynamic Projection MH08 Quick Installation Manual Download Page 8

Channel

Function

Value

Destination

Description

001

PAN high

0 - 255

Mirror motors

PAN High Byte

002

PAN low

0 - 255

Mirror motors

PAN Low Byte

003

TILT high

0 - 255

Mirror motors

TILT High Byte

004

TILT low

0 - 255

Mirror motors

TILT Low Byte

005

Mirror Reset

255

Mirror motors

Starts mirror recalibration

006

Picture mute off

0 - 10

RS232 / projector

Disables picture mute

006

Picture mute on

20 - 30

RS232 / projector

Enables picture mute

006

Shutter off

40 - 50

RS232 / projector

Disables the mechanical shutter

006

Shutter on

60 - 70

RS232 / projector

Enables the mechanical shutter

006

Picture freeze off

100 - 110

RS232 / projector

Disables picture freeze

006

Picture freeze on

120 - 130

RS232 / projector

Enables picture freeze

007

Image orientation 1

10 - 63

RS232 / projector

Image orientation mode 1

007

Image orientation 2

64 - 127

RS232 / projector

Image orientation mode 2

007

Image orientation 3

128 - 192

RS232 / projector

Image orientation mode 3

007

Image orientation 4

192 - 255

RS232 / projector

Image orientation mode 4

008

reserved

-

-

-

009

Motor and LED drivers on

28 - 38

Mirror motors & LED

Turns the drivers on

009

Motor and LED drivers off

50 - 58

Mirror motors & LED

Turns the drivers off

009

Lamp mode 1

130 - 138

RS232 / projector

Lamp power mode 1

009

Lamp mode 2

150 - 158

RS232 / projector

Lamp power mode 2

009

Lamp mode 3

170 - 178

RS232 / projector

Lamp power mode 3

009

Lamp on

230 - 238

RS232 / projector

Lamp lamp on

009

Lamp off

250 - 255

RS232 / projector

Lamp lamp off

010

LED intensity 

0 - 255

LED

Main intensity of the combined RGB LEDs

011

LED red

0 - 255

LED

Red LED intensity

012

LED green

0 - 255

LED

Green LED intensity

013

LED blue

0 - 255

LED

Blue LED intensity

014

reserved

-

-

-

Valid for firmware version 1.3.26

8

Copyright © 2014 - 2022 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com

Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice. 

DMX fixture definition for v1.3.26

In order to control the Mirror Head at least a 14 channel DMX Master is required no matter what kind of Mirror Head and/or function 
of the fixture you use (see section „Using and operations“ for details).

av

ailable f

or 

MH08 – MH1

3 only

QIG - Version 2.8

Mirror Head Quick Installation Guide

For the full manual please visit 

https://www.dynamicprojection.com/mh-support/

Summary of Contents for MH08











Reviews: