Dynam E-Razor, Instruction Manual

Page: 2 / 9

,, !"#$
%&'()*+-#,./0123456789:
1,
2,=>!"?@ABCDE,FGH IJKLMNOPQRST,UVWXCYZ['@
\]^_.
3,
4,67cdWXefgRhJ,ijO4klmno$p(qrOs%5t"uv.
5,! 67cdxy4kz{|}~,/€‚ƒ#„ †‡.ˆ‰€Š‹ŒJ.
As the user of this product, you are solely responsible for operating it in a manner that
does not endanger yourself and others or result in damage to the product or the property
of others.This model is controlled by a radio signal that is subject to interference from many
sources outside your control. This interference can cause momentary loss of control so it is
advisable to always keep a safe distance in all directions around your model, as this margin
will help to avoid collisions or injury.
Never operate your model with low transmitter batteries.
Avoid operating your model in the street where injury or damage can occur.Always
operate your model in an open area away from cars, traffic, or people.Never operate
the model out into the street or populated areas for any reason.
Carefully follow the directions and warnings for this and any optional support equipment
(chargers, rechargeable battery packs, etc.) that you use.
Keep all chemicals, small parts and anything electrical out of the reach of children
Moisture causes damage to electronics. Avoid water exposure to all equipment not
specifically designed and protected for this purpose.
Never lick or place any portion of your model in your mouth as it could cause serious injury
or even death
1.
2.
3.
4.
5.
FG!"ŽK%R†‘,FGU’ y„“,FG”•–U’ —˜™M
š ›,!"œ”žPMš ›—Ÿ U’ y.
cd¡¢,£¤,¥ ¦,§¨,©ª£«+-Ž¬,­®¯°–±Ž¬t"!". ­®¯
²³o´µ,¶·¸¹«º»´µ.
/¼„ ½¾¿ÀÁ –Ÿ y˜™,&„ ½ÂÃÄÅÆÇÈÉÊ
/¼ ›ËÌ̈́ ËÎÏЄ ½Ë3CELLËÎ,&ÄÅÆ@¿)Ô)É
Õֿ׌11.1V 2200MAH #$ÝÞ ›4k12VßÐ,1.0A„ àR#$
ÌÍá,„ &âã¿:2.5ä&。æ„ çÂÃÄÅÆè¿ÉÊ.
,
.
•–U’ ,¼éêëìínî,¼!"ï(F.MODE)–Ÿ
NORMï.
÷¼ ›øùoú¬ûüý,÷˜™oÏþÿ
þ.
Battery Charging and Warning
ø
›˜™
2 3
WARNINGS
Contents
Œ
1
2
3
5
4
1. E-RAZOR 450 RTF Airframe
2. 6CH R/C System
3
4. 11.1V 2200MAH 15C Li-Po Battery
5. Balancing Charger
. Adaptor
›„ k
It is important that you only charge the included 3S 11.1V 2200mAh Li-Po Battery with the
included 3S 11.1V 1.0-Amp Li-Po Balancing Charger. Your battery is equipped with special
Charge Protection Circuitry and Balance Charge Leads with connector that are only
compatible with this charger. Attempting to charge the battery using another Li-Po charger
or non Li-Po compatible charger could result in serious damage. Please familiarize yourself
thoroughly with the Battery Warnings and Guidelines section before continuing.The
included 3S 11.1V 1.0-Amp Li-Po Balancing Charger will charge a near fully discharged
(not over-discharged) 3S 11.1V 2200mAh Li-Po battery in approximately 1.52.0 hours. In
some cases the charge time may be shorter depending on the actual amount of capacity
left in the battery after a flight. NEVER charge the battery unattended.
The Li-Po battery included with your e-razor 3D will arrive partially charged. For this
reason the initial charge may only take approximately 3050 minutes.
The charger requires up to 3-Amps of 11.515 Volt DC input power that can be supplied by
the optional AC to 12V DC, 3-Amp Power Supply for convenient charging anywhere an
AC outlet is available. NEVER attempt to power the charger from an AC outlet without the
use of a proper AC to DC adapter/power supply.
Not e: ic Not e: ic
:
FG„ |} K； ›1! 5„ ；t"Ÿ˜™?F#
F；‚â&á ›¾„ ½˜™；67!"&,¶· ›~
ç.
:
HELICOPTER LI-PO BATTERY CONNECT
1.
Turn the transmitter on first and lower the throttle/
collective stick Completely ,put the flight mode is
NORM mode
.
2.
Once the battery has been properly positioned, fasten the
hook and look strap around the battery for added security.
Then, plug the battery into the battery lead of the ESC.