Dynalco UM-200 Installation And Operation Manual Download Page 11

Page: 11 / 12

Additional instructions for current users of Dynalco models TID-110 or STM-110 series
temperature monitors

The following products may be upgraded to the model UM-200 monitor:

TID110-11

J type thermocouple (displays in DegF)

TID110-12

J type thermocouple (displays in DegC)

TID110-13

K type thermocouple (displays in DegF)

TID110-14

K type thermocouple (displays in DegC)

STM110-11

J type thermocouple (displays in DegF)

STM110-12

J type thermocouple (displays in DegC)

STM110-13

K type thermocouple (displays in DegF)

STM110-14

K type thermocouple (displays in DegC)

Please see the programming steps in this manual for configuring the proper thermocouple
type and display in either DegF or DegC. Replacing the STM-110 series will also require
setting up the over temp alarm.

Summary of Contents for UM-200













Search results

Summary of Contents for UM-200

Reviews:

Related manuals for UM-200

Brands by name

Popular brands

Dynalco UM-200, Installation And Operation Manual

Search results

Summary of Contents for UM-200

Reviews:

Related manuals for UM-200

Brands by name

Popular brands