Dynalabs DYN-C-1000-LN Product Manual Download Page 2

  

 

 

 

  

 

All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors.

 

 

 

Product Support 

If  at  any  time  you  have  questions  or  problems  with  the  DYN-C-1000-LN 
sensors, please contact a Dynalabs engineer at

Phone:                   +90 312 266 33 34   (9 a.m. to 5 p.m., UTC +3) 

E-mail:                   [email protected] 

Warranty 

Our products are warranted against defective materials and workmanship for one 
year.

 

Defects arising from user errors are not covered by the warranty. 

Copyright 

All  copyrights  of  this  manual  belonging  to  Dynalabs  products  are  reserved.  It 
cannot be reproduced without written consent. 

Disclaimer 

Dynalabs  Ltd.  provides  this  publication  "as  is"  without  warranty  of  any  kind, 
express  or  implied,  including  but  not  limited  to,  the  implied  warranties  of 
merchantability  or  fitness  for  a  particular  purpose.  This  document  is  subject  to 
change  without  notice,  and  should  not  be  construed  as  a  commitment  or 
representation by Dynalabs Ltd. 

This publication may contain inaccuracies or typographical errors. Dynalabs Ltd. 
will periodically update the material for inclusion in new editions. Changes and 
improvements to the product described in this manual may be made at any time. 

 

 

 

 

Summary of Contents for DYN-C-1000-LN









Reviews: