Dynacraft MULTI-SPEED Owner'S Manual Download Page 48

Page: 48 / 125

ASSEMBLY

ASSEMBL

CHECK YOUR BRAKES

Press each brake lever to make sure that there is no binding and that the brake pads press hard enough on the

rims to stop the bike. The brake pads should be adjusted so they are 1 mm to 2 mm away from the rim when

the brakes are not applied. Brake pads should be centered on the rim and the rear portion of each brake pad

should be about 0.5 - 1.0 mm farther from the rim than the front portion of the brake pad.

Brake pad aligned with the

rim surface.

Pad and rim should be parallel.

Direction of rim rotation.

CAUTION

Do not ride the bicycle until the brakes are

functioning properly. To test, apply the brakes while

trying to push the bike forward to make sure they

will stop the bicycle. Never ride a bicycle that is not

functioning properly.

WARNING

Sudden or excessive application of the front brake

may pitch the rider over the handlebars, causing

serious injury or death.

Summary of Contents for MULTI-SPEED






























































































































Search results

Summary of Contents for MULTI-SPEED

Reviews:

Related manuals for MULTI-SPEED

Brands by name

Popular brands

Dynacraft MULTI-SPEED, Owner'S Manual

Search results

Summary of Contents for MULTI-SPEED

Reviews:

Related manuals for MULTI-SPEED

Brands by name

Popular brands