background image

22

TROUBLESHOOTING GUIDE

Problem

Electric dirt bike does not run

 

Electric dirt bike suddenly stops 

working while in use 

 

Short run time (less than 15 minutes 

per charge)

Possible Cause

 

Undercharged battery

Loose wires or connectors

Tripped thermal fuse

Motor or electrical switch

Undercharged battery

Tires are not properly inflated

Brakes are not adjusted properly

Solution

Charge the battery. A new battery 

should have been charged for at least 

18 hours before using the vehicle for 

the first time. After first-time use, 

recharge the battery for at least 12 

hours after each use. Never charge 

the battery longer than 30 hours.

Check all connections. Make sure 

the charger port is plugged into the 

charging port on the electric dirt bike 

and that the charger is plugged into 

the wall outlet.

Check all wires and connectors to 

make sure they are tight.

The built-in thermal fuse may “trip” 

and shut down operation of the 

electric dirt bike if the electric dirt 

bike is overloaded or the driving 

conditions too severe. Once a fuse 

has tripped, release the throttle and 

wait 25 seconds before operating 

the electric dirt bike again. To avoid 

repeated automatic shutdowns, do 

not overload the electric dirt bike 

by exceeding the 140 lb maximum 

weight capacity or by towing 

anything behind the electric dirt bike. 

Do not drive up hills or run into fixed 

objects, which can cause the wheels 

to stop spinning while power is still 

being supplied to the motor.

Contact Dynacraft for repair or 

replacement

Charge the battery. A new battery 

should have been charged for at least 

18 hours before using the product for 

the first time and up to 12 hours after 

each subsequent use.

Check all wires and connectors. 

Make sure the battery connector 

is tightly plugged into the charger 

connector and that the charger is 

plugged into the wall outlet.

The tires are inflated when shipped 

butinvariably will lose some pressure 

between the point of manufacturing 

and your purchase. Refer to the 

instructions on page 12.

Adjust the brakes pursuant to the 

instructions on page 16.

Summary of Contents for 8802-33






























Reviews: