(PD97•54)
57083 Vacuum Adapter
57065 Cone Muffler
57066 Muffler Body
95526O-Ring
57446 Vac Nozzle
57067 Vac Tube
57093 Vacuum Adapter
57066 Muffler Body
56028 Muffler Cap
57065 Cone Muffler
57066 Muffler Body
56027 Muffler Insert (2)
56028 Muffler Cap
Machine Exhaust Assemblies
Self Generated Vacuum (Vac-Ready) / Machine Exhaust
Central Vacuum / Machine Exhaust
Non-Vacuum / Machine Exhaust
2
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade
®
Abrasive Power Tool.
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Operating Instructions:
Warning: Eye, face and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow safety
procedures posted in workplace.
1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2. Connect power source to tool. Be careful not to depress throttle lever in the process.
3. Check tool speed with tachometer. If tool is operating at a higher speed than the SPM marked on the tool or operating improperly, the tool should be
serviced to correct the cause before use.
Maintenance Instructions:
Products offered by Dynabrade should not be converted or otherwise altered from original design without expressed written consent
from Dynabrade, Inc.
1. All Dynabrade air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example : if the tool
specification state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) is recommended.
2. Mineral spirits are recommended when cleaning tool. Do not clean tool with any solvents or oils containing concentrated acids, esters, ketones, chlorinated
hydrocarbons or nitro hydrocarbons.
3. An air line filter-regulator-lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11289 Air Line Filter-
Regulator-Lubricator— Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic
components. Operates 28 CFM @ 90 PSI has 3/8" NPT female ports.
4. Frequent drainage of water traps in air lines is recommended.
5. Some silencers on air tools may clog with use. Clean and replace as required.
6. A motor tune-up kit (P/N 96107) is available which includes assorted parts to help maintain motor in tip-top shape.
Safety Instructions:
•
Warning: Eye, face and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death Follow safety
procedures posted in workplace.
•
Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
•
Tool SPM must never exceed abrasive/sanding pad SPM rating, regardless of tool capacity.
•
Operate machine for 30 seconds before application to workpiece to determine if machine is safely performing before work begins.
•
Always disconnect power supply before changing abrasive or making machine adjustments.
•
Inspect abrasives and sanding pads for damage or defects prior to and during operation of tool.
•
Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.
•
Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
57065Cone Muffler
56027 Muffler Insert (2)
One Year Warranty:
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date
of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or
replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to
have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety
practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal
performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
96197 Dowel Pin
