2
(APD00•12)
Full One Year Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date
of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or
replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have
been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety prac-
tices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal performance.
Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
Machine
Pad
Length
Weight
Height
Air Flow Rate
Sound
Motor
Motor
Air Pressure
Description
Inch (mm)
Inch (mm)
Pound (kg)
Inch (mm)
SCFM (LPM)
Level
HP (W)
RPM
PSIG (Bars)
10700
8" (203)
12" (305)
4.3 (1.95)
5" (127)
28 (793)
85.6 dBA
.46 (343)
900
90 (6.2)
10705
8" (203)
12" (305)
4.3 (1.95)
5" (127)
28 (793)
93.0 dBA
.46 (343)
900
90 (6.2)
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose I.D. Size 3/8" (10 mm)
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade
®
Abrasive Power Tool.
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade Rotary Vane air tools must be used with a filter-regulator-lubricator to maintain all warranties.
Operating Instructions:
Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death.
Follow safety procedures posted in workplace.
1. With power source disconnected from tool, securely fasten abrasive/sanding pad on tool.
2. Connect power source to tool. Be careful not to depress throttle lever in the process.
3. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be
serviced to correct the cause before use.
4. To avoid the danger of contaminating the workpiece from the lubricating oils permeating the air or sanding dust, it is recommended that this machine be
hooked up to a central vacuum system or one of our unique vacuum systems that gather all such contaminants in a paper or cloth dust bag. This self
contained vacuum system is highly efficient and convenient to use since it does not need to be attached to a separate vacuum system and is as mobile
as the machine itself.
Maintenance Instructions:
Products offered by Dynabrade should not be converted or otherwise altered from original design without the expressed written
consent from Dynabrade, Inc.
1. All Dynabrade Rotary Vane air motors should be lubricated with two drops of Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) placed directly into the air
inlet with throttle lever depressed every four hours of use.
2. Gears on the 8” Gear Driven should be greased with Dynabrade 95541 Grease Gun and 95542 Grease (10 oz. 283.5g.). Apply grease to the grease
fitting in the mounting plate, one full plunge every 300 hours of use.
3. 57360 Felt Wiper should be replaced every 600 hours.
4. An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11405 Air Line
Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and positive-drip lubrication of
pneumatic components. Operates 40 SCFM @ 100 PSIG has 3/8" NPT female ports.
5. Frequent drainage of water traps in air lines is recommended.
6. Some silencers on air tools may clog with use. Clean and replace as required.
7. A Motor Tune-Up Kit (P/N 96195) is available which includes assorted parts to help maintain and repair motor.
•
Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or
death. Follow safety procedures posted in workplace.
•
Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute
•
Tool RPM must never exceed abrasive/sanding pad RPM rating, regardless of tool capacity.
•
Operate machine for 30 seconds before application to workpiece to determine if machine is working properly and safely before work begins.
•
Always disconnect power supply before changing abrasive or making machine adjustments.
•
Inspect abrasives and sanding pads for damage or defects prior to and during operation of tool.
•
Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.
•
Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
Notice
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is con-
tingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of lubrication
during the use of this tool.
Note: To order replacement parts specify the model and serial number of your machine.
Safety Instructions:
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
