5
COPIES
SYM
MULTIPLE COPIES +
• Your Labelmaker can provide multiple copies
within the range 1-99
• To use this facility press
then
COPIES
SYM
to show n = 1 on the display. To increase the
number of copies required press
.
By pressing
you can work backwards
from 99.
To print the desired quantity press
.
Note: Labels will be printed with a short leader
and trailer. A row of vertical dots will print
between each label as a cutting guide; the final
label will have a long trailer ready for cutting.
INCREMENTAL NUMBERING
Labels can be printed in increments of 1-99
automatically.
• Key in your starting number as the right most
digit on the label. Press
then
1.2
.3
..n
,
the display will automatically move up a digit
to the next number. Press
then
1.2
.3
..n
to continue the sequence.
• It is also possible to include automatic
incremental numbering when printing
multiple copies.
• Key in your starting number, eg. LABEL 1 .
Next press
then
COPIES
SYM
followed by
until the desired number of
copies are displayed eg.10.
Now press
then
1.2
.3
..n
. This will print
ten labels - LABEL 1 to LABEL 10 .
• It is possible to print up to 99 sequentially
numbered labels at any one time.
Note: Labels are printed with short leaders and
trailers. See "multiple copies" above.
LAST LABEL MEMORY
• The unit will store the last label text and
settings when turned off. Upon power-up,
these will be restored and displayed.
Removal of the batteries for more than a few
seconds will cause this information to be lost.
Symbols and special characters
INTERNATIONAL CHARACTERS
To add a diacritical (accent) to create an
international character, enter the character first,
followed immediately by the diacritical, e.g. press
E
followed by
then
'
to get
é
.
To add a diacritical to an existing character, use
or
to place the cursor under the
character to be changed, then press the
appropriate diacritical key.
SYMBOLS
Press
SYM
to show symbols and special
characters, some of which are not available direct
from the keyboard. The display will show:
A-L?
Each letter selects a line of symbol characters, as
shown in the table on page 2.
Press
DEL
to cancel, or press a letter key ‘A’ to
‘L’ until you find the line of symbols required.
Use
or
to select a symbol. Press
to place the symbol in the label.
PRINT CONTRAST - May be adjusted by pressing
SYM
followed by
Y
to display the five
contrast symbols .
• Use
or
to select lighter or darker
print.
• Press
to confirm the setting. The contrast
level will revert to the mid-setting when the
Labelmaker is turned off and on again.
Note: This function enables you to adjust the
print quality under extreme temperature
conditions.
Cleaning
• Clean the cutter blade regularly: Remove the
cassette, then insert the tip of a ball pen or
pencil between L-shaped piece
D
➊
and the
guide pin – see page 2.
• Press and hold down cutter lever
E
➊
to
expose cutter blade
D
➋
,
then use a cotton bud
and alcohol to clean both sides of the blade.
Release cutter lever
E
➊
.
• Check and clean print head face
D
➌
regularly
using a cotton bud and alcohol ONLY.
Troubleshooting
No display
• check machine is on
• replace discharged batteries
• check AC adaptor.
No printing or poor text
• replace discharged batteries
• check tape cassette installed correctly
• clean the print head
• replace the tape cassette.
Tape jammed
• lift out tape cassette carefully
• remove/release jammed tape
• DO NOT cut the ink ribbon – turn spool
to
tighten
• cut off excess label tape
• refit/replace the tape cassette.
Poor cutter performance
• clean the cutter blade regularly
Continued overleaf.
