dymax 40077 User Manual Download Page 18

Page: 18 / 28

Dymax BlueWave® 75 User Guide

Figure 18. Bulb Replacement Step 5

Pivot the white Bulb Clamp in place and tighten the two knurled screws. Plug in the Bulb Connector
(Figure 19).

Figure 19. Bulb Replacement Step 6

Replace the unit’s cover and tighten the four cover fasteners. Once the cover is secure, power up the unit

and using a small screw driver press the Reset Button located on the back of the unit. This will reset the
Bulb Hour Meter but not extinguish the Change Bulb Indicator Light. Cycle the system power once to reset
the Change Bulb Indicator Light.

Figure 20. Bulb Replacement Step 7

Note: Fan Filters (included with replacement bulbs) MUST also be replaced during a bulb change.

Once the new Bulb is installed and operational, it is recommended that the intensity is set again (see
Settings and Adjustments Instructions).

Reset

Button

Fan Filter

Screw

Bulb Connector

Side Wire

(located “inward”)

Summary of Contents for 40077





























Search results

Summary of Contents for 40077

Reviews:

Related manuals for 40077

Brands by name

Popular brands

dymax 40077, User Manual

Search results

Summary of Contents for 40077

Reviews:

Related manuals for 40077

Brands by name

Popular brands