- 7 -
DXE-SNS-CT1 - Compression Tool for Snap-N-Seal 75 ohm Coaxial Connectors
Ratchet compression tool for installing
DXE-SNS6
Snap-N-Seal coaxial connectors. Ordinary pliers will not
install these connectors properly.
DXE-SNS6-25 - Watertight Coaxial Connector, Snap-N-Seal for CATV F-6 Cable, 25 pieces
Snap-N-Seal is an environmentally sealed CATV F coaxial connector system for harsh environments. The connectors have a unique,
360 degree radial compression system that offers the signal leakage protection required for high performance receive systems.
Quad sealed system prevents moisture from migrating into the connection
360 degree radial compression provides superior RF integrity (-95 dB typical, 60% bonded foil cable)
Easy cable preparation
Connector to cable retention of 40 lbs minimum
Superb impedance match to 1 GHz
Manufactured of high quality 360 brass, cadmium plated with yellow chromate coating for maximum
corrosion resistance
UV-resistant plastic and O-rings provide a reliable environmentally sealed connector
An installation tool, such as the
DXE-SNS-CT1
is required to install the connectors. Normal crimping tools or pliers will not work.
DXE-CIT-1 - F Connector Tightening Tool
The CIT-1 installs and removes F connectors in high density and hard to reach locations, and is the only tool that works
with bent coax. Only finger force is required. Provides enough leverage to achieve a 30 in/lb tightening force by hand.
Helps insure proper connections thereby reducing the potential of loose connector related service calls.
PTX-82180 - Permatex® Black RTV Sealant, Non-Acetic - 3.3 oz Tube, Black RTV Sealant
By Permatex®.
We have all used RTV to seal water out of things, right? Have you ever sealed a piece of electronic gear with it --
then opened it some time later to find that it had still managed to become corroded inside? Guess what? It's not the
rain that corroded it - It's the RTV! Normal RTV gives off acetic acid when it cures. That's the vinegar smell. The
acetic acid causes the corrosion. DX Engineering has located a Neutral Cure RTV made right here in Ohio that is
non-corrosive and is safe for sealing those baluns and other electronic gear that are going to be out in the weather.
Applies just like "normal" RTV, dries in one hour and cures in 24 hours at 70 degrees F. And it doesn't smell like
vinegar!
3.3 oz. Tube, Black
*This part is classified hazardous and is limited to domestic UPS Ground shipping only
PTX-22058 - Permatex® Dielectric grease, 3 oz.
Dielectric grease is ideal for keeping moisture from entering your coaxial connectors. It also acts as a lubricant allowing easy
connector removal by stopping corrosion of electrical connectors. Multi-use 3 oz package.
Safe for all RF connections.
DXE-RLP-75FF - Lightning Protector, Receive 75Ω, DC Pass, F Conn
Unique In-Line® design is impedance matched to 75Ω and is virtually transparent to all analog or digital bi-directional signals from
DC to 1.0 GHz. Tii's patented proprietary coaxial gas tube surge protector is equipped with an integral fail short mechanism for a
power-cross condition which shunts both the coaxial cable’s center conductor and sheath for a common path to
ground. The DC breakdown voltage of the protector provides superior protection against transient surges, yet is
compatible with network powered applications. The protection element is designed to reset after each over
voltage event. Metallic housing of the Tii In-Line® Coaxial Lightning Surge Protector provides necessary EMI
shielding. When properly connected the protector is environmentally sealed (15 psi) to prevent ingress of
moisture and humidity encountered in broadband pedestals, vaults, NIDs and stand alone applications. Full 360˚
“F” port connectors provide superior RF performance and tighter connections
