- 4 -
Fully insert the PL-259 to the balun and tighten the collar. Loop the cable through the ‘P’ clamps
and form approximately a 6” diameter loop of cable.
Mount the ‘P’ clamps on both sides of the bracket using the hardware (1”
bolt, 1/4” spacer, 3 star washers, and Nyloc nut) as shown in
Figure 6
.
Using pliers will help hold the clamps and parts together while you get
the Nyloc nut started.
Once the cable is aligned between the balun and the first ‘P’ clamp,
tighten the bolt, star washer, and nut at the balun end of the bracket.
Ensure the cable going through the ‘P’ clamps is properly aligned and has
the loop. Tighten all the parts holding the ‘P’ clamps in place.
Figure 6
The completed Cable Strain
Relief kit installation
should
look like
Figure 7
.
Figure 7
Weatherproofing
The PL-259 connected to the balun (or other device) should be weatherproofed using
DXE-3M2155
- 3M Temflex™ and
TRM-06132 -
Scotch® Super 33+ available from DX Engineering.
Technical Support
If you have questions about this product, or if you experience difficulties during the installation,
contact DX Engineering at (330) 572-3200. You can also e-mail us at:
For best service, please take a few minutes to review this manual before you call.
Warranty
All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one (1) year from date of shipment. DX
Engineering’s sole obligation under these warranties shall be to issue credit, repair or replace any item or part thereof which is proved to be other than as warranted; no
allowance shall be made for any labor charges of Buyer for replacement of parts, adjustment or repairs, or any other work, unless such charges are authorized in advance by
DX Engineering. If DX Engineering’s products are claimed to be defective in material or workmanship, DX Engineering shall, upon prompt notice thereof, issue shipping
instructions for return to DX Engineering (transportation-charges prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived by
Buyer unless made in writing. The above warranties shall not extend to any products or parts thereof which have been subjected to any misuse or neglect, damaged by
accident, rendered defective by reason of improper installation, damaged from severe weather including floods, or abnormal environmental conditions such as prolonged
exposure to corrosives or power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any goods or parts thereof furnished by
Buyer or acquired from others at Buyer’s specifications. In addition, DX Engineering’s warranties do not extend to other equipment and parts manufactured by others
except to the extent of the original manufacturer’s warranty to DX Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof.
These warranties provide exclusive remedies, expressly in lieu of all other remedies including claims for special or consequential damages. SELLER NEITHER MAKES
NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY NOT
STRICTLY IN ACCORDANCE WITH THE FOREGOING.
©DX Engineering 2017
DX Engineering
®
, DXE
®
, DX Engineering, Inc.
®
, Hot Rodz
®
, Maxi-Core
®
, DX Engineering THUNDERBOLT
®
, DX Engineering Yagi Mechanical
®
, EZ-BUILD
®
,
TELREX
®
, Gorilla Grip
®
Stainless Steel Boom Clamps, Butternut
®
, SkyHawk™, SkyLark™, SecureMount™, OMNI-
TILT
™, RF-PRO-1B
®
, AFHD-4
®
are trademarks of
PDS Electronics, Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands and product names are the
trademarks of their respective owners.
Specifications subject to change without notice
