Dwyer Instruments DS-300 Series Installation And Operating Instructions Download Page 3

1-3/4 (44.45)

1-11/16 (42.86)

1-5/8 (41.27) TYP

1-15/16 (49.21)

LP

HP

1/4 MALE NPT

5/16 (7.94)

Using the appropriate differential pressure equation from Page 4 of this bulletin,calculate the differential pressure generated by
the sensor under normal operating conditions of the system. Check the chart below to determine if this value is within the
recommended operating range for the sensor. Note that the data in this chart is limited to standard conditions of air at 60°F
(15.6°C) and 14.7 psia static line pressure or water at 70°F (21.1°C). To determine recommended operating ranges of other 
gases, liquids an/or operating conditions, consult factory.

Note:

the column on the right side of the chart which defines velocity ranges to avoid. Continuous operation within these

ranges can result in damage to the flow sensor caused by excess vibration. 

Flow Calculations and Charts 

The following information contains tables and equations for
determining the differential pressure developed by the DS-
300 Flow Sensor for various flow rates of water, steam, air
or other gases in different pipe sizes.

This information can be used to prepare conversion charts
to translate the differential pressure readings being sensed
into the equivalent flow rate. When direct readout of flow is
required, use this information to calculate the full flow
differential pressure in order to specify the exact range of
Dwyer Magnehelic

®

or Capsuhelic

®

gage required. Special

ranges and calculations are available for these gages at
minimal extra cost. See bulletins A-30 and F-41 for
additional information on Magnehelic

®

and Capsuhelic

®

gages and DS-300 flow sensors.

For additional useful information on making flow
calculations, the following service is recommended: Crane
Valve Co. Technical Paper No. 410 “Flow of Fluids Through
Valves, Fittings and Pipe.” It is available from Crane Valve
Company, www.cranevalve.com. 

Pipe Size

(Schedule 40)

1

1-1/4

1-1/2

2

2-1/2

3

4

6

8

10

Flow

Coefficient

“K”

0.52

0.58

0.58

0.64

0.62

0.67

0.67

0.71

0.67

0.70

Operating Ranges

Air @ 60°F & 14.7 psia

(D/P in. W.C.)

1.10 to 186

1.15 to 157

0.38 to 115

0.75 to 75

1.72 to 53

0.39 to 35

0.28 to 34

0.64 to 11

0.10 to 10

0.17 to 22

Operating Ranges

Water @ 70°F
(D/P in. W.C.)

4.00 to 675

4.18 to 568

1.36 to 417

2.72 to 271

6.22 to 193

1.43 to 127

1.02 to 123

2.31 to 40

0.37 to 37

0.60 to 79

Velocity Ranges

Not Recommended

(Feet per Second)

146 to 220

113 to 170

96 to 144

71 to 108

56 to 85

42 to 64

28 to 43

15 to 23

9.5 to 15

6.4 to 10

REVISEDBulletin F-50  7/8/04  8:04 AM  Page 3

1.800.868.7495

QualityInstruments-Direct

.ca

Summary of Contents for DS-300 Series

Page 1: ... pointed upstream The top connection is for static or low pressure Location The sensor should be installed in the flowing line with as much straight run of pipe upstream as possible A rule of thumb is to allow 10 15 pipe diameters upstream and 5 downstream The table below lists recommended up and down piping PRESSURE AND TEMPERATURE Maximum 200 psig 13 78 bar at 200 F 93 3 C Series DS 300 Flow Sen...

Page 2: ...6 to allow for thermal expansion 5 Tighten packing gland nut finger tight Then tighten nut with a wrench an additional 1 1 4 turns Be sure to hold the sensor body with a second wrench to prevent the sensor from turning INSTRUMENT CONNECTION Connect the slide pressure tap to the high pressure port of the Magnehelic air only or Capsuhelic gage or transmitting instrument and the top connection to the...

Page 3: ...e the differential pressure readings being sensed into the equivalent flow rate When direct readout of flow is required use this information to calculate the full flow differential pressure in order to specify the exact range of Dwyer Magnehelic or Capsuhelic gage required Special ranges and calculations are available for these gages at minimal extra cost See bulletins A 30 and F 41 for additional...

Page 4: ...ssure expressed in inches of water column Q Flow expressed in GPM SCFM or PPH as shown in equation K Flow coefficient See values tabulated on Pg 3 D Inside diameter of line size expressed in inches For square or rectangular ducts use D 4 x Height x Width π P Static Line pressure psia T Temperature in degrees Fahrenheit plus 460 Rankine p Density of medium in pounds per square foot Sf Sp Gr at flow...

Reviews: