Faucet Installation Guide:
1. Remove retaining nut and washers (B,C,D) from the threaded retaining post (A).
2. With the retaining post (A) screwed into the faucet ring (F), insert the stainless steel
supply lines (G) and retaining post (A) through the faucet hole in your counter top.
3. While supporting the faucet, reinstall the rubber washer (B), metal washer (C) and
retaing nut (D). Screw the locking screws (E) out of the retaining nut until they
become flush with the bottom of the retaining nut (D).
4. Tighten the retaining nut (D) until it contacts the metal washer (C) on the underside
of the counter top and snug the locking screws using a phillips head screwdriver
being sure not to over tighten.
5. Connect the water supply lines (G) to the shut-off valves (I) via the attached
compression fitting (H) with an adjustable wrench being sure not to over tighten.
6. Remove the faucet aerator end (J) before turning the water supply on to ensure
debris in the lines passes through easily being sure to flush both the hot and cold
lines before reinstalling the aerator.
M
Drain Installation Guide:
1. Unscrew drain tube (#6)
from drain body and wrap
tephlon tape around
threaded end of drain tube (#6).
2. Unscrew lock nut (#5) from
drain body. Remove gasket
(#3), and washer (#4) from
drain body. Screw the drain
tube (#6) back into drain body.
3. Put a bead of 100% Silicone
USE OF PLUMBERS PUTTY VOIDS WARRANTY
USE OF PLUMBERS PUTTY VOIDS WARRANTY
sealer under flange (#1), or
use flange gasket (#2) and
insert threaded end of drain
body down through drain hole.
4. Replace gasket (#3) beveled
side up, then the washer (#4) and
thread up lock nut (#5) from the underside of the lavatory sink until the black rubber (#3) gasket is seated
securely inside the opening of the drain hole in the counter top. Tighten lock nut (#5) carefully, wiping
excess silicone from around the edge of the flange (#1).
Ideally, it is best to wait 24 hours and tighten
further to allow for a solid silicone seal. Over tightening can squeaze out too
much silicone possibly
preventing a proper seal. Allow 24 hours for sealant to set.
DO NOT OVERTIGHTEN OR
DAMAGE WILL OCCUR!
DO NOT OVERTIGHTEN OR
DAMAGE WILL OCCUR!
5. Install drain t rap assembly and leak test all connections.
6
4
3
1
5
MAXIMUM
COUNTERTOP
THICKNESS = 2-1/2"
2
D’VONTZ • 7208 EAST 38th STREET • TULSA, OKLAHOMA 74145
918.622.3600 • FAX 918.622.3649 • WWW.DVONTZ.COM
If you have any trouble during the installation of your D’Vontz drain, please call our Customer Service
department at 918-622-3600.
Congratulations on the successful installation of your D’Vontz faucet!
LIMITED WARRANTY
•
Use of any cleaning products other than those suggested by D’Vontz will void warranty. See
care and installation instructions included with product or available on the web at
www.dvontz.com
.
•
Use of “plumber’s pu y” on any product will void all warranties!
•
All D’Vontz products are warranted to the original purchaser to be free of defects in material
and workmanship for one year from the purchase date.
•
This limited warranty only applies to the original purchaser of our product. Proof of Purchase
in the form of the original sales receipt will be required for any warranty claim.
•
This limited warranty does not cover any costs associated with a product’s removal and/or
reinstallation, including labor, materials or damage to surrounding products or goods.
•
There is no warranty on copper sink or tub patinas. Please refer to the care instructions
included with these products.
D’V
ontz L.L.C.
7208 E. 38th St.,
T
ulsa, Oklahoma 74145
800-322-3600 ph
918-622-3649 fax
