DVB RRBR-02 Installation Manual Download Page 1

6400 SYCAMORE CANYON BLVD. 

RIVERSIDE, CALIFORNIA 92507

855-680-9595

WWW.DV8OFFROAD.COM

PRODUCT 

INSTALLATION 

MANUAL

4 DOOR HARDTOP 

ROOF RACK

 

2021+ FORD BRONCO 
RRBR-02

TOOLS

 REQUIRED

 

SKILL

 LEVEL

 

TIME

 REQUIRED

 

-10mm wrench 
-13mm Socket 
-3mm, 4mm Aleen Bit

Before you install this kit — 

Read and understand all 

instructions, warnings, cautions, and notes contained in 

this installation instruction guide. Consult your vehicle 

owner’s manual for proper disconnection of electrical and 

lifting of vehicle if required for installation of this product.  
This install may require some technical skills and 

knowledge of basic mechanical work. If you do not feel that 

you are capable of performing this install please take this 

product to a trained professional.  
After reading this guide please contact us with any 

questions or concerns before installing product.  

Customer Service: 855-680-9595 

DV8 Offroad is not responsible for any bodily injury or harm to you 

or your vehicle as a result of an improper install.

Proper installation of this kit required knowledge of the factory 

recommended procedures for removal and installation of original 

equipment components. We recommend that the factory shop manual 

and any special tools needed to service your vehicle be on hand during 

the installation. Installation of this kit without proper knowledge of the 

factory recommended procedures may affect the performance of these 
components and the safety of the vehicle 

 

• Always wear eye protection when operating power tools

 

Inspect all contents of this package to make sure product is not damaged 

and all installation hardware has been included. If parts are missing from 

kit, please be prepared to provide the following information 

1. Name of purchase location 
2. Bar Code on side of box 
3. Date above bar code  
4. Date inside box cover 

 

- Novice/Intermediate 
- 1 (you) to 2 persons 

Little skill level required, you can 

easily assemble this by yourself, 

however will need assistance for 

installation 

- 3 Hours  

Time to install this should take 

about 3 hours 

WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION

855-680-9595

NEED HELP?

Summary of Contents for RRBR-02









Reviews: