Dux Prodigy 5 135DB5N Owner'S Manual Download Page 15

Owner’s Manual – Prodigy 5

13

H3109    3109    Rev. J

System Maintenance

Regular servicing will help to keep 
the water heater operating safely and 
efficiently.

Six Month Service:

This service may be carried out by the 
owner.
1.  Stand clear of the Pressure & 

Temperature Relief (PTR) Valve drain 
pipe outlet.

2.  Open the PTR Valve for 

approximately 10 seconds by 
lifting the easing lever on the valve. 
Confirm water discharges to waste 
through the drain pipe.

3.  Lower the easing lever gently and 

check it closes correctly.

4.  Repeat the above process for the 

expansion control valve (if installed).

Other than this, personally inspecting or 
servicing any part of the water heater is 
not recommended.

 

Annual Service:

This service should only be carried 
out by a licensed tradesperson. We 
recommend your local Dux Service 
Agent.
The service should include the following: 
•  Inspect and flush the PTR Valve and 

expansion control valve (if installed). 

•  Check the spark gap, gas control 

valve and thermocouple. 

•  Check and if necessary adjust the 

main burner pressure. 

•  Clean and check the main burner 

and the pilot light. 

Five Year Service:

This service should only be carried 
out by a licensed tradesperson. We 
recommend your local Dux Service 
Agent.
In locations where the water has Total 
Dissolved Solids (TDS) exceeding 600 
mg/L, this service is recommended 
every 3 years.
In addition to the items listed in the 
Annual Service, this service should 
include the following:
•  Replace the PTR Valve.
•  Replace the anode.
•  Drain and flush the water heater.

Summary of Contents for Prodigy 5 135DB5N





















Reviews: