REMPLACEMENT DES LAMES DE LA RACLETTE
ATTACHEZ/RELÂCHEZ L’ENTRAÎNEMENT
Ouvrez le clip (Réf. 1).
Retirez les deux dispositifs de retenues de la lame (Réf. 2)
en les poussant vers l’extérieur et extraire la lame. Retirez la lame.
Réutilisez la même lame en inversant le bord en contact avec
le plancher jusqu’à ce que les quatre bords soient usés
ou remplacez-la par une nouvelle lame en la fixant sur les vis
sur le corps de la raclette.
Repositionnez les deux dispositifs de pression de la lame
en centrant la partie la plus large du corps de la raclette
sur les fentes des pièces de fixation, puis poussez les dispositifs
de pression de la lame vers l’intérieur.
Fermez le crochet à nouveau.
Replacez la raclette sur son support, en suivant les instructions décrites
précédemment.
Placez la brosse sous la tête, au centre (auto-récureuse à brosse
unique), placez les brosses sous la tête des deux côtés (auto-récuresue
à double brosse), mettez la machine en marche.
Appuyez sur l’interrupteur ON-OFF, une fois après le démarrage, la
machine libère la fixation de la brosse. Le bouton n’est activé que
lorsque toutes les fonctions sont désactivées (moteur d’aspiration et
brosses).
Ref. 1
Ref. 2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•
rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•
Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank float
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet filter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•
rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•
Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank float
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet filter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
ENTRETIEN QUOTIDIEN
Nettoyez le réservoir d’eau sale.
Assurez-vous que le sceau extérieur
des couvercles est propre et non
endommagé. Remplacez-le si
nécessaire.
Assurez-vous que le filtre de sortie
du détergent est propre et exempt
de débris.
Assurez-vous que les brosses/
tampon d’entraînement sont
propres et non usés. Remplacez-les
si nécessaire.
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•
rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•
Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank float
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet filter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•
rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•
Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank float
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet filter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•
rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•
Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank float
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet filter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•
rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•
Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank float
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet filter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•
rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•
Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank float
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet filter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
Assurez-vous que la raclette est
propre et que les lames ne sont pas
usées.
POUR CHARGER LES
BATTERIES
Branchez le chargeur autonome
dans le port de charge rouge
pour charger les batteries s’il
n’est pas équipé d’un chargeur
de bord.
REMARQUE :
n’arrêtez jamais la
charge avant la fin du cycle (feu
vert).
REPLACING THE SQUEEGEE BLADES
ATTACHING/REMOVING THE BRUSH
Attaching the brush:
•
rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush
engages..
Removing the brush:
•
Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.
DAILY MAINTENANCE
Clean the dirty
water tank.
Check the dirty water tank float
is undamaged and clean and
moves freely on the pin.
Check that the
detergent outlet filter
is clean.
Check that the
brush is clean.
Check that the
squeegee is clean
and the blades are not
worn.
Open the clip (Ref. 1).
Remove the two blade retainers (Ref. 2) by pushing them outwards then extracting them.
Remove the blade.
Reuse the same blade by reversing the edge in contact with the floor until all four edges are worn out, or replace with a new blade, fitting it onto the
screws on the body of the squeegee.
Reposition the two blade pressing devices by centering the wider part of the slots on the squeegee body fastening pins, then push the blade pressing
devices inwards.
Close the hook again.
Replace the squeegee on its support, following the instructions described previously.
PLDC02099
BATTERY
CHARGER ON
BOARD
1
2
Les Produits Dustbane Ltée, 25 pl. Pickering, Ottawa, ON K1G 5P4
•
Tél : 1-800-387-8226 Fax : 1-800-363-5309 www.dustbane.ca