manualshive.com logo in svg

Durr EcoGun AS MAN 1AF, Operation Manual

Share
Download
Durr EcoGun AS MAN 1AF Operation Manual Download Page 19

8.2 

Defects table

Visualizer of typical spray pattern problems

Spray pattern

Fault identification

Spray jet is distorted.

Spray jet is bent or tapered.

Spray jet is too thick in the middle.

Spray jet is split.

Spray jet is uneven (pulsating).

Fault description

Cause

Remedy

No material

Flow cup empty

Check flow cup. Top up, if necessary.

Material escapes at the
needle gland.

Needle gland worn
out

Replace needle gland  

Ä

 8.3.3

“Replace needle gland”.

Needle gland loose

Tighten needle gland sensitively.

Air escapes between valve
pin and housing.

Valve seal worn out.

Replace valve seal  

Ä

 8.3.2 “Replacing

valve seal”.

Spray jet is distorted.

Air cap is misaligned. Rotate air cap into the required posi-

tion.  

Ä

 6.4 “Alignment of the air cap”

Spray jet is bent or tapered.

Bores in air cap are
soiled.

Clean and check air cap. Replace air

cap if defective  

Ä

 7.2 “Cleaning”.

Faults

11/2017

EcoGun AS MAN 1AF - MSG00020EN

19/36

Summary of Contents for EcoGun AS MAN 1AF





































Reviews:

No comments

Brands by name

Popular brands

Load more brands