DuroStar DS13000DX User Manual Download Page 17

Page: 17 / 76

9. Fuel Switch

14. Battery Switch

10. Propane Inlet

11. Engine Switch

12. Charging Light

13. Low Oil Alert

15. Idle Control

16. Circuit Breaker

17. Multimeter

19. 50A Receptacle

20. 240V 4-Prong Twist Lock

21. GFCI 20A Receptacles

18. CO Alert

22. 120V 3-Prong Twist Lock

13.

Low Oil Alert

– Will light only if the generator shuts down due to low oil.

14.

Battery Switch

– Prevents battery discharge during storage.

15.

Idle Control

- Slows the engine to save fuel and lower noise when no load.

16.

Circuit Breaker -

Protects the panel from overload and short circuits.

17.

Multimeter

– Displays voltage, hertz, and time running.

18.

CO Alert -

Shuts down the engine in the event of CO buildup.

19.

120/240V 4-Prong Receptacle

- Use to connect electrical devices that run 120 or 240 volt,

60Hz, single-phase, AC current (NEMA 14-50).

20.

120/240V 4-Prong Twist Lock

- Use to connect electrical devices that run 120 or 240 volt, 60Hz,

single-phase, AC current (NEMA L14-30).

21.

120v 3-Prong GFCI Receptacle

- Use to connect electrical devices that run 120 volt, 60Hz,

single-phase, AC current (NEMA 5-20).

22.

120v 3-Prong Twist Lock

- Use to connect electrical devices that run 120 volt, 60 Hz, single-

phase, AC current (L5-30).

Summary of Contents for DS13000DX













































































Search results

Summary of Contents for DS13000DX

Reviews:

Related manuals for DS13000DX

Brands by name

Popular brands

DuroStar DS13000DX, User Manual

Search results

Summary of Contents for DS13000DX

Reviews:

Related manuals for DS13000DX

Brands by name

Popular brands