manualshive.com logo in svg

DUROMAX XP5500E, User Manual

Share
Download
DUROMAX XP5500E User Manual Download Page 18

GENERATOR COMPONENTS

18

2. Choke Lever 

1. Air Cleaner

10. Volt Meter

8. 120v 3-Prong 

Receptacle

6. 120/240v 4-Prong 

Receptacle

19. Power Boost

5. Circuit Breaker

7. Ground Terminal

9. Battery

12. Oil Fill and Dipstick

13. Engine Switch

14. Recoil Start

11. 12v DC Charging 

Posts

1. 

Air Cleaner

 - a removable, cleanable, oiled, sponge-like element that cleans the air going into 

the engine.

2. 

Choke Lever

 - Allows the airflow into the carburetor to be restricted to assist in starting the 

engine.

3. 

Fuel Gauge

 - Indicates the amount of fuel in the gasoline tank.

4. 

Fuel Cap

 - Allows access to fill the gasoline tank.

5. 

Circuit Breaker

 - Resettable switch that protects the generator from electrical overload.

6. 

120/240v 4-Prong Receptacle

 - Use to connect electrical devices that run 120 or 240 Volt, 

60Hz, single phase, AC current (NEMA L14-30).

7. 

Ground Terminal

 - Connect a ground wire here to properly ground the generator.

8. 

120v 3-Prong Receptacle

 - Use to connect electrical devices that run 120 Volt, 60 Hz, single 

phase, AC current (NEMA 5-20).

9. 

Battery

 - 12V DC 7ah Battery that powers the Electric Start System.

10. 

Volt Meter

 - Provides reading of voltage output.

16. Fuel Valve

Summary of Contents for XP5500E













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands