DUROMAX XP4500DX Page 60 User Manual Download

Page: 60 / 74

TROUBLESHOOTING

Problem

Description

Solution

The engine will not

start

Engine switch is “OFF”

Set engine switch to “RUN”

Fuel Valve is “CLOSED”

Turn the fuel valve to “OPEN”

Choke is open

Close the choke

The engine is out of fuel

Add fuel

Fuel is old or contaminated

Change fuel

Spark plug is dirty

Clean spark plug

Spark plug is broken

Replace spark plug

The generator is not level

Move the generator to a level
surface

Oil is low

Add/change the oil

Engine runs, but there

is no electrical output

The circuit breaker is “OFF”

Turn “ON” circuit breaker

Wiring connection is bad

Replace extension cord(s)

Device connected to generator
is malfunctioning

Disconnect malfunctioning
device

The generator runs

but does not support

all electrical devices

connected

Generator is overloaded

Disconnect 1 or more items to
reduce the load

Device connected to the gener-
ator is bad

Disconnect malfunctioning
device

The air filter is dirty

Clean / replace the air filter

Summary of Contents for XP4500DX











































































Search results

Summary of Contents for XP4500DX

Reviews:

Related manuals for XP4500DX

Brands by name

Popular brands

DUROMAX XP4500DX, User Manual

Search results

Summary of Contents for XP4500DX

Reviews:

Related manuals for XP4500DX

Brands by name

Popular brands