manualshive.com logo in svg

DUROMAX XP4000S, User Manual

Share
Download
DUROMAX XP4000S User Manual Download Page 12

17.  Muffler

GENERATOR COMPONENTS

12

2. Choke Lever 

1. Air Cleaner

9. Volt Meter

5. Circuit Breaker

8. 120V 30A Twist Lock

6. 120V 3-Prong 

Recepticle

7. Ground Terminal

11. Oil Fill and Dipstick

12. Engine Switch

13. Recoil Start

1. 

Air Cleaner - a removable, cleanable, oiled, sponge-like element that cleans the air going into 

the engine.

2. 

Choke Lever - Allows the airflow into the carburetor to be restricted to assist in starting the 

engine.

3. 

Fuel Gauge - Indicates the amount of fuel in the gasoline tank.

4. 

Fuel Cap - Allows access to fill the gasoline tank.

5. 

Circuit Breaker - Resettable switch that protects the generator from electrical overload.

6. 

120v 3-Prong Receptacle - Use to connect electrical devices that run 120 Volt, 60 Hz, single 

phase, AC current (NEMA 5-20).

7. 

Ground Terminal - Connect a ground wire here to properly ground the generator.

8. 

120v 3-Prong Twist Lock - Use to connect electrical devices that run 120 Volt, 60 Hz, single 

phase, AC current (L5-30).

9. 

Volt Meter - Provides reading of voltage output.

15. Fuel Valve

Summary of Contents for XP4000S































































Reviews:

No comments

Brands by name

Popular brands

Load more brands