DUROMAX XP12000X User Manual Download Page 17

Page: 17 / 72

12. Battery Switch

9. Engine Switch

10. Charging Light

11. Low Oil Alert

13. Idle Control

14. Circuit Breaker

15. Multimeter

17. 50A Receptacle

18. 240V 4-Prong Twist Lock

19. GFCI 20A Receptacles

16. CO Alert

20. 120V 3-Prong Twist Lock

13.

Idle Control

- Slows the engine to save fuel and lower noise when no load.

14.

Circuit Breaker -

Protects the panel from overload and short circuits.

15.

Multimeter

– Displays voltage, hertz, and time running.

16.

CO Alert -

Shuts down the engine in the event of CO buildup.

17.

120/240V 4-Prong Receptacle

- Use to connect electrical devices that run 120 or 240 volt,

60Hz, single-phase, AC current (NEMA 14-50).

18.

120/240V 4-Prong Twist Lock

- Use to connect electrical devices that run 120 or 240 volt, 60Hz,

single-phase, AC current (NEMA L14-30).

19.

120v 3-Prong GFCI Receptacle

- Use to connect electrical devices that run 120 volt, 60Hz,

single-phase, AC current (NEMA 5-20).

20.

120v 3-Prong Twist Lock

- Use to connect electrical devices that run 120 volt, 60 Hz, single-

phase, AC current (L5-30).

Summary of Contents for XP12000X









































































Search results

Summary of Contents for XP12000X

Reviews:

Brands by name

Popular brands

DUROMAX XP12000X, User Manual

Search results

Summary of Contents for XP12000X

Reviews:

Brands by name

Popular brands