manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 43

Aligning the needle bar linkage

Service manual H867 Version 00.0 - 08/2013

41

10 Aligning the needle bar linkage

Sequence

First check the following settings:

• A straight and undamaged needle has to be inserted 

(

 Betriebsanleitung Kap. 7.3 Nadel einsetzen und wechseln

)

Correct setting

Upper stitch length adjusting wheel to 0:

The needle pierces exactly in the center of the feed-dog needle hole.

10.1 Moving the needle bar linkage sideways

Cover

• Arm cover 

(

 Section 

4.4.2 Removing and fitting the arm cover

, 

page 11)

•

Head cover (

 Section 

4.4.3 Removing and fitting the head cover

, 

page 11)

Figure 32: Aligning the needle bar linkage sideways

Setting steps

1. Position the upper stitch length adjusting wheel to 0.

2. Loosen the setscrews  (1) on the two adjusting rings  (2) at the right-hand 

end of the shaft for the needle bar linkage.

Risk of injury

Switch off the sewing machine before aligning the needle bar 
linkage sideways.

WARNING

 

1

2

4

3

(1) - Setscrews
(2) - Adjusting rings

(3) - Needle hole
(4) - Needle bar linkage

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands