background image

A  MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE 

TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) 

TO COMBUSTIBLE MATERIALS. IT IS OF THE UTMOST 

IMPORTANCE THAT PELLETVENT BE INSTALLED ONLY IN 

ACCORDANCE WITH THESE INSTRUCTIONS.

LISTED

MH8381

MH14420

NOTE:

Read through all of these instructions before 
beginning your installation. Failure to install 
as described in this instruction will void the 
manufacturer’s warranty, and may have an 
effect on your homeowner’s insurance and 
UL listing status. Keep these instructions for 
future reference. This booklet also contains 
instructions for installing a venting system 
within an existing masonry chimney, and 
for installations passing through a cathedral 
ceiling.
 

Dear Customer, Installer, or End User:

We welcome any comments regarding 
matters pertaining to our DuraVent products.  
We welcome any ideas, input or complaints 
and I’ll make sure that someone responds 
directly back to you.
Send your emails to: 
[email protected]

If you are searching for tech support or 
product information, please phone us at 
800-835-4429.
Or email us at:
[email protected]

Summary of Contents for PelletVent

















Reviews: