4 hours
place the UPS away from other units at least 20 cm to avoid interference. DO NOT operate the UPS
where the temperature and humidity is outside the specific limits. (Please check the specs for the
limitations.)
2. Charging
Plug in the AC input cord to the wall outlet. For the best results,
suggest charging the battery at least 4 hours before initial use. The
unit charges its battery while connecting to the utility.
3. Connection of Equipment
Plug in the loads to output receptacles on the rear panel of the UPS.
Simply turn on the power switch of UPS unit, then devices
connected to the UPS will be protected by UPS unit.
4. Connection of Network
To surge protect a network connection, connect a network cable from the wall jack outlet to the IN
jack of the UPS. Then connect a network cable from the OUT jack of the UPS to the network
device.
5. Connection of Communication
UPS equipped with communication port allows monitoring and controlling from computer screen.
Connect one end of a communication cable to your PC and the other to the com port at the rear of
the UPS.
ViewPower is an UPS power management software, allowing users to control and monitor UPS
straightly from PC monitor. Insert ViewPower software CD or download ViewPower software from
http://www.power-software-download.com
to your hard drive. Follow on-screen instructions to
complete the software installation.
After computer is restarted, ViewPower is geared and presents as an orange plug icon located in
the system tray at the right-bottom corner.
6. Turn On/Off
To turn on the UPS, press power switch lightly. To turn off the UPS, please press power switch
again.
7.
Green Power Function
DM615N-650 and DM615N-850 UPS are equipped with Green Power Function. For saving power
and protecting battery, the method of deep discharging protection is adopted on inverter mode.
Trouble-shooting
Use the table below to solve minor problems. If any abnormal situations occur that are not listed
above, please call service technician for assistance.
Problem
Possible Cause
Solutions
No LED display on
the front panel.
Low battery.
Charge the UPS at least 6 hours.
Battery fault.
Replace the battery with the same type of
battery.
The UPS is not turned on.
Press the power switch again to turn on the
UPS.
Alarm continuously
sounds when the
mains is normal.
The UPS is overload.
Remove some loads first. Before reconnecting
equipment, please verify that the load matches
the UPS capability specified in the specs.
When power fails,
back-up time is
shortened.
The UPS is overload.
Remove some critical load.
Battery voltage is too low.
Charge the UPS at least 6 hours.
Battery defect. It might be due to high
temperature operation environment, or
improper operation to battery.
Replace the battery with the same type of
battery.
The mains is normal,
but LED blinks..
Power cord is loose.
Reconnect the power cord properly.
Specifications
Model
650
850
1000
1500
2000
CAPACITY
650VA/
360W
850VA/
480W
1000VA/
600W
1500VA/
900W
2000VA/
1200W
INPUT
Voltage
110/120 VAC or 220/230/240 VAC
Voltage Range
81-145 VAC / 162-290 VAC
OUTPUT
Voltage Regulation
+/-10%
Transfer Time
Typical 2-6 ms, 10 ms max.
Waveform
Simulated Sine Wave
BATTERY
Type & Number
12V/7AHx1
12V/9AHx1
12V/7AHx2
12 V/9 AH x 2
Charging Time
4-6 hours recover to 90% capacity
PHYSICAL
Dimension, DxWxH, (mm)
287x100x142
350x146x 160
397x146x205
Net Weight (kgs)
4.25
4.90
8.0
11.1
11.5
Environment
Humidity
0-90 % RH @ 0-40° C (non-condensing)
Noise Level
Less than 40 dB
MANAGEMENT
USB
Supports Windows 98 SE/ME/NT 4.x/2000/2003/XP/Vista/2008
* Product specifications are subject to change without further notice.
