manualshive.com logo in svg

DuraMax 26063, Owner'S Manual, Page: 2 / 11

Share
Download
DuraMax 26063 Owner'S Manual Download Page 2

TABLE OF CONTENTS

………………………………………………………………………………….…………..…………………3

………………………………………………………………………….…………..…………………2

2

PRODUCT SPECIFICATIONS

PRODUCT SPECIFICATIONS

SAFETY INFORMATION

………………………………………………………………………….…………..……………….4/6

ASSEMBLY INSTRUCTIONS

CUTTING HEIGHT ADJUSTMENT

BLADE ADJUSTMENT

………………………………………………………………….…………..…………....…..

………………………………………………………………….…………..…………....…....................7

7

CARE AND MAINTENANCE

…………………………………………………………………………….…………..………………….3

CHECKING THE ADJUSTMENT

……………………………………………………………….…………..……………..........……8

…………………………………………………………………………….…………..……………………………

…………………………………………………………………………….…………..……………….....

…………………………………………………………………………….…………..……………………………..…

…………………………………………………………………………….…………..…………...............

…………………………………………………………………………….…………..

TWO-YEAR LIMITED WARRANTY

…………………………………………………………………….…………..……………….. 9

PARTS DIAGRAM

……………………………………………………………………………………………….…………..…… 10/11

16’’ (40.6cm) REEL MOWER

Item No.
Cutting Path
Height Adjustments
Wheel Qty.
Weight

289516

16’’ (40.6cm)

1 - 2-1/8’’ (2.5-5.3cm)

2

28.4lb (12.8Kg)

Summary of Contents for 26063












Reviews:

No comments