DuraMAC 5030CVSPBUSS Installation & Operation Manual Download Page 3

 

10 

Notes:

 

 

EXTENSION CORDS: For best performance, it is recommended to connect the AC 
transformer power cord directly to a grounded GFCI outlet.  The use of extension cords is 
NOT recommended.  

Do not use the power cord or discharge hose to carry or handle the pump. Doing so may 
cause  damage  to  the  power  cord  or  discharge  hose.    Use  the  carrying  handle  supplied 
with the pump. 

Always use a grounded outlet to attach the plug.  A three-prong mating type receptacle is 
needed for safe use.  This should be in accordance with the National Electric Code and any 
additional codes or laws required by your local government.   

It  is  strongly  recommended  to  use  a  ground  fault  interrupt  device  on  any  electrical 
appliance,  including  this  pump,  when  used  in  a  wet  or  moist  environment.    This  GFCI 
(ground fault  circuit  interrupter)  should  be  listed  by Underwriters Laboratories (UL).   This 
is  required  by  many  local  codes  and  enforcement  agencies.    It  is  strongly  recommended 
by A.Y. McDonald as it provides a much safer installation and will greatly reduce possible 
injury from electrical shock. 

Your pump has thermal over-load protection built in.  It is not recommended for pumping 
liquids over 120°F.  The thermal overload protector will automatically shut down the pump 
in an overheat situation.  It will then reset itself once the pump cools down. The pump will 
then work again.  This overload is designed as a safety device and it will fail after repeated 
use.  Normal operation is for fluids between 32°F & 120°F.  

DO NOT RUN THE PUMPS DRY. The pumps depends on water for cooling and lubrication.  
Operating the pumps without water may cause the motor to overheat or cause damage to 
parts of the pump.  It may also shorten the life of your pumps. 

EXTENSION CORDS: For best performance, it is recommended to connect the power cord 
directly to the grounded GFCI outlet.  If the use of an extension cord is necessary, always 
use a grounded waterproof type cord.  Never use longer than a 25-ft. cord that is lighter 
than 14/3 gauge.  

A qualified electrician must perform all wiring. 

Summary of Contents for 5030CVSPBUSS







Reviews: