background image

Safety

vi

975-0445-01-01

This guide for use by qualified installers only

6. To reduce the risk of electrical shock, disconnect DC power from the 

Duracell Inverter 3000

 before attempting any maintenance or 

cleaning or working on any circuits connected to the 

Duracell 

Inverter 3000

. Turning off controls will not reduce this risk.

7. The 

Duracell Inverter 3000

 must be provided with equipment-

grounding conductors connected to the vehicle chassis as described in 

“Chassis Ground Wire Sizing” on page 2–8

 and 

“Output Conductor 

Selection for Hardwire Installation” on page 2–8

Precautions When Working With Batteries

1. Follow all instructions published by the battery manufacturer and the 

manufacturer of the equipment in which the battery is installed to 
reduce the risk of battery explosion.

2. Working in the vicinity of lead-acid batteries is dangerous. Batteries 

generate explosive gases during normal operation. Therefore, you 
must read this guide and follow the instructions exactly before 
installing or using your 

Duracell Inverter 3000

.

3. This equipment contains components which tend to produce arcs or 

sparks. To prevent fire or explosion, do not install the 

Duracell 

Inverter 3000

 in compartments containing batteries or flammable 

materials, or in locations that require ignition-protected equipment. 
This includes any space containing gasoline-powered machinery, fuel 
tanks, as well as joints, fittings, or other connections between 
components of the fuel system.

4. Make sure the area around the battery is well ventilated.

5. Never smoke or allow a spark or flame near the engine or batteries.

6. Use caution to reduce the risk or dropping a metal tool on the battery. 

It could spark or short circuit the battery or other electrical parts and 
could cause an explosion.

7. If you need to remove a battery, always remove the ground terminal 

from the battery first. Make sure all accessories are off so you don’t 
cause a spark.

WARNING: Explosion or fire hazard

Inverter_3000_Install_Guide.book  Page vi  Tuesday, June 3, 2008  12:22 PM

Summary of Contents for Inverter 3000






































Reviews: