3
OPERATING INSTRUCTIONS
Operating the Spotlight
To turn the Spotlight ON, depress the Trigger. To turn the Spotlight OFF, release the Trigger.
To lock the Trigger in the ON position, squeeze the Trigger and move the Trigger Lock Switch
(located on the side of the handle) to the “locked” position. The Spotlight will stay on until the
lock is moved to the “unlocked” position and the Trigger released.
Operating the LED Area Lights
The ON/OFF pushbutton for the LED Area Lights is located on the top of the Spotlight.
Using the Built-In Workstand and Carry Lanyard
Turn the Spotlight upside-down on a smooth even surface, and rest it on the Workstand/Carry
Handle.
The Carry Lanyard may be used to store or carry the Spotlight. Adjust the slide on the cords to
keep the Lanyard secure around the supporting object.
CARE AND MAINTENANCE
All batteries lose charge with time, especially when they are warm. Recharge the unit every
two months when not in frequent use, preferably using the 120 volt AC method.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the
spotlight unit with a soft cloth moistened with a mild solution of water and detergent.
The quartz halogen bulb is the only user-replaceable part in the Spotlight. Periodically inspect the
condition of adapters, connectors and wires. Contact Technical Support toll-free at (866) 584-
5504 to replace any components that have become worn or broken.
Spotlight Bulb Replacement
To replace the bulb, you will need a small Phillips screwdriver and a 12 volt H3 75 watt
replacement bulb. During installation, avoid touching the glass part of the bulb. Bulb life may
be shortened by installing a bulb with dirt or fingerprints on it. The bulb can be wiped clean
with a cloth moistened with alcohol.
1. Disconnect the unit from any charging adapters.
2. Push the rubber bezel forward toward the front of the spotlight to reveal two small Phillips
screws in the retaining ring.
RETAINING RING
RUBBER
“O” RING
REFLECTOR
RUBBER
END
CAP
RUBBER GUARD COVER
TRIGGER LOCK
TRIGGER
QUARTZ HALOGEN
BULB
TRIGGER
TRIGGER LOCK
2
CHARGING/RECHARGING THE SPOTLIGHT
This unit is shipped in a partially charged state. Charge unit BEFORE first use using the 120
Volt AC Charger for 20-30 hours or until the green Battery Status LED lights. Charge after each
use until green LED lights.
Charging/Recharging Using the 120 Volt AC Charger
and a Standard Household Extension Cord (not included)
Plug a standard North American 120 volt AC extension cord into the 120 Volt AC Charger on
the back of the unit.
Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not
depressed).
Charge until the green Battery Status LED Indicator lights (approximately 20-30 hours). DO
NOT CHARGE FOR LONGER THAN 30 HOURS.
Charging/Recharging Using the 12 Volt DC Charging
Adapter
Plug the barrel tip of the supplied 12 Volt DC Charging Adapter into the 12 Volt DC Charging
Port.
Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC
power source.
Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not
depressed).
Charge until the green Battery Status LED Indicator lights (approximately 3-4 hours) when the
Battery Level Display pushbutton is pressed. DO NOT CHARGE FOR LONGER THAN 4
HOURS.
Make sure the DC source (jump-starter, battery pack, vehicle accessory outlet, etc.) is 12 volt
DC and is able to supply at least one half amp at 12 volt DC for 8 hours. This means a battery
pack should be charged with at least 4 amp hours capacity.
Note:
When using a vehicle’s 12 volt DC accessory outlet as a charging source, be
aware that some vehicles require you to turn on the ignition to power the
accessory outlet.
WARNING
• NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT
SIMULTANEOUSLY.
BUILT-IN 120V
AC CHARGER
BATTERY STATUS
LED INDICATORS
HOUSEHOLD EXTENSION CORD
(NOT INCLUDED)
12 VOLT DC
CHARGING PORT
12 VOLT DC CHARGING ADAPTER
VEC157SDB_ManualEN_071306.qxp 7/18/06 5:29 PM Page 2
