Durabrand CB130DR8, Service Manual

Page: 17 / 55

5-2 P7100EA
2. Initial Setting
General
1. Enter the Service mode. (See page 5-1.)
2. Press [VOL
n
] button on the service remote
control unit. Display changes “C/D,” “7F,” “SOUND
TYPE,” “VIDEO,” “1000,” “YUV MEMORY,”
“TUNER A/M/S,” “QAM,” “DTV-H,” “D-SOUND,”
and “DL V-CHIP” cyclically when [VOL
n
] button is
pressed.
3. To set the following each data value, press [CH
o
/
p
] buttons on the service remote control unit.
7F --- Set to “FF.”
SOUND TYPE --- Set to “MONO.”
VIDEO --- Set to “V1/V2.”
1000 (monitoring time) --- Set to “1000.”
YUV MEMORY --- Set to “OFF.”
TUNER A/M/S --- Set it by indication of TUNER
as follows
UTUNATSMS001: Set it in “M.”
UTUNATSSP001: Set it in “S.”
QAM --- Set to “135.”
DTV-H --- Set to “B.”
D-SOUND --- Set to “STEREO.”
DL V-CHIP --- Set to “ON.”
3. Setting for BRIGHT, CONTRAST,
COLOR, S-COLOR, C-COLOR,
TINT, V-TINT, S-TINT, C-TINT,
SHARP, S-SHARP, and C-SHARP
Data Values
General
1. Enter the Service mode. (See page 5-1.)
2. Press [MENU] button on the service remote
control unit. Display changes “BRT,” “CNT,” “CLR,”
“S-CLR,” “C-CLR,” “TNT,” “V-TNT,” “S-TNT,” “C-
TNT,” “SHARP,” “S-SRP,” and “C-SRP,” cyclically
when [MENU] button is pressed.
CNT
1. Press [MENU] button on the service remote
control unit. Then select “CONTRAST” (CNT)
display.
2. Press [CH
o
/
p
] buttons on the service remote
control unit so that the value of “CONTRAST”
(CNT) becomes 84.
CLR
1. Press [MENU] button on the service remote
control unit. Then select “COLOR” (CLR) display.
2. Press [CH
o
/
p
] buttons on the service remote
control unit so that the value of “COLOR” (CLR)
becomes 58.
S-CLR
1. Press [MENU] button on the service remote
control unit. Then select “S-COLOR” (S-CLR)
display.
2. Press [CH
o
/
p
] buttons on the service remote
control unit so that the value of “S-COLOR” (S-
CLR) becomes 58.
C-CLR
1. Press [MENU] button on the service remote
control unit. Then select “C-COLOR” (C-CLR)
display.
2. Press [CH
o
/
p
] buttons on the service remote
control unit so that the value of “C-COLOR” (C-
CLR) becomes 66.
TNT
1. Press [MENU] button on the service remote
control unit. Then select “TINT” (TNT) display.
2. Press [CH
o
/
p
] buttons on the service remote
control unit so that the value of “TINT” (TNT)
becomes 54.
V-TNT
1. Press [MENU] button on the service remote
control unit. Then select “V-TINT” (V-TNT) display.
2. Press [CH
o
/
p
] buttons on the service remote
control unit so that the value of “V-TINT” (V-TNT)
becomes 58.
S-TNT
1. Press [MENU] button on the service remote
control unit. Then select “S-TINT” (S-TNT) display.
2. Press [CH
o
/
p
] buttons on the service remote
control unit so that the value of “S-TINT” (S-TNT)
becomes 58.
C-TNT
1. Press [MENU] button on the service remote
control unit. Then select “C-TINT” (C-TNT) display.
2. Press [CH
o
/
p
] buttons on the service remote
control unit so that the value of “C-TINT” (C-TNT)
becomes 59.
SHARP
1. Press [MENU] button on the service remote
control unit. Then select “SHARP” (SHARP)
display.
2. Press [CH
o
/
p
] buttons on the service remote
control unit and select “43.”
S-SRP
1. Press [MENU] button on the service remote
control unit. Then select “S-SHARP” (S-SRP)
display.