background image

2

(Fig. 2)

ON mode:

Slide the switch to the ON position, the system will remain ON all the time no matter the power cord is

connected or not. Only remote transmitter is disabled.

REMOTE mode:

Slide the switch to the REMOTE position (middle), the system will ONLY operate with receiving

commands from the remote transmitter.

OFF mode:

Slide the switch to the OFF position, the system will remain OFF all the time. Remote transmitter and

Receiver box are both disabled.

NOTE: The OFF mode is strongly recommended if house is unattended for a long time. For safety, placing the slide

switch in the OFF position also functions as a safety “LOCK-OUT” by both turning the system off and disable the remote

receiver.

LEARN / PAIR TRANSMITTER WITH RECEIVER BOX

Pair the transmitter with receiver first if they do NOT communicate. To have the receiver box to accept the transmitter’s

signal (code), please follow the steps below:

1. Unplug the receiver box from power source before LEARN process. Then, plug-in again.

2. Slide the switch to “REMOTE”. Install the RF antenna onto receiver box.

3. Press the “LEARN” button on receiver (Fig. 1) for 1 second, then the receiver box will

sounds of quick BEEP X 2 (♫, ♫)

.

4. Press the ON button on transmitter. The receiver box will

sounds of quick BEEP X 3 (♫, ♫, ♫)

to indicate that the

transmitter’s code has been captured by the receiver. It means the LEARN process is completed.

If you fail the LEARNING of matching the security code, please wait 2 minutes before another try. The interval allows the

microprocessor in the receiver box to reset itself and available for accepting new code. Please try more times.

Any questions, please email us.

([email protected])

WARNING & REMINDER

This system MUST be installed exactly as complied with these instructions. Read all instructions before

installation, and follow them during installation carefully.

Any modifications of Durablow remote control system, or parts, or components are PROHIBITED. They will void

the warranty, and may cause a fire hazard result in human casualties and property damages.

Do NOT connect any gas valve or electronic module directly to power source.

Read gas appliance manufacturer’s instructions and wiring schematics completely for proper placement of all

wires. All electronic modules are to be wired to manufacturer’s specifications.

All wiring diagrams in these instructions are for illustration purpose ONLY. Follow instructions from manufacturers of

gas valve and electronic module for correct wiring & installation procedures. Improper installation of electric

components can cause damage to electronic module, gas valve and remote receiver.

PRE - INSTALLATION

Decide where to install the receiver box before proceeding. Less

metallic shielding / blocking, better signal strength.

The remote receiver box can be placed on the fireplace, under the fireplace, behind the control panel or louvers....etc.

Keep away from high-heat of exceeding 130°F. Additional protection is required for no exposure to the heat. Make sure

the receiver box’s slide switch is in the OFF position before installation.

Summary of Contents for TR2001








Reviews: