background image

7

Hard Rock Tone

3 Channel Set-up

Channel #1: (Bypass mode) Amplifier’s clean tone.

Channel #2: Twin Tube rhythm channel (dirty rhythm tone)

Channel #3: Twin Tube lead channel (dirty lead tone)

3-Channels of Distortion

Channel #1:  (Bypass mode) Amplifier set for slightly dirty 

rhythm tone.

Channel #2: Twin Tube rhythm channel adds overdrive.

Channel #3: Twin Tube lead channel adds higher saturation for 

leads.

2-Channel Set-up.

(Amp is set clean)

Channel #1: Twin Tube rhythm channel set for clean tone.

Channel #2: Twin Tube lead channel set for moderate 

distortion.

         

bass       treble

vol          gain

vol            gain

 

The ¼” mono instrument cable that leaves your guitarʼs jack plugs into the Twin 

Tube Classicʼs jack marked “Input.” The cable that exits from the “Output” jack on 

the Twin Tube Classic goes to the next effect in the signal chain, or to the amplifier. 

When first activating the Twin Tube Classic, start with the Rhythm Channel Volume 

and Gain control knobs in the full counter-clockwise position. Then, start rotating 

the knobs clockwise until the desired volume level and overdrive are achieved. 

Next, with the Lead Channel Volume and Gain control knobs in the full counter-

clockwise position, depress the Channel Selector switch. This mutes the Rhythm 

Channel and activates the Lead Channel. As with the Rhythm Channel, start 

rotating the knobs clockwise until the desired volume level and distortion are 

achieved, relative to the Rhythm Channel and to the bypassed sound of the Twin 

Tube Classic.

Experiment with different Volume and Gain settings. Some of the coolest tones 

are achieved with a little discovery. Because of the Twin Tube Classicʼs incredible 

amount of gain and distortion in the Lead Channel, be aware that extreme settings 

can result in uncontrollable feedback. And, as always, musicians and audience 

members are best advised to use ear protection when exposed to loud volume.

Here are some sample settings to get your started:

Basic Operation

Three Channel Setup

Channel #1:  (Bypass mode) Amplifierʼs clean tone.

Channel #2: Twin Tube Classic rhythm channel (dirty rhythm).

Channel #3: Twin Tube Classic lead channel (dirty lead tone)

Tone

Rhythm

Lead

Classic/Straight-Ahead Rock n’ Roll Tone

Summary of Contents for Twin Tube Classic













Reviews: