background image

3

Item

Part No.

Description

Qty.

1

Refer Below

Main Frame Assembly

1

2

43061

FY 508M Bearing Housing

2

3

Refer P 4

Triple K Tine Complete with K25 Point 

(Refer Table for Quantities)

4

43145

YAR208-108-2F Y Bearing 1

1/

2

2

5

Refer P 4

Tine Clamp                                       

(Refer Table for Quantities)

6

4920260

Top Link Spacer Assembly

1

7

4920284

LH Crumbler Support Assembly

1

8

4920285

RH Crumbler Support Assembly

1

9

4920294

LH Crumbler Arm Assembly

1

10

4920510

RH Link Support Stay

1

11

4920515

LH Link Support Stay

1

12

4920520

RH & LH Rear Link Stay

2

13

Refer Below

Front Stay

1

14

Refer Below

Rear Stay

1

15

4920580

RH Rear Stay Top Anchor

1

16

4920581

LH Rear Stay Top Anchor

1

17

4920585

Top Link 12” Centre Tube

2

18

Refer Below

Crumbler Assembly

1

19

4920642

Crumbler Axle Retainer

1

20

4920643

Crumbler Axle Endcap

1

21

4920645

Crumbler Spacer (14.5mm)

1

22

45019

M12 x 30 Class 8.8 Zinc Plated Bolt

2

23

45029

M12 x 80 Class 8.8 Zinc Plated Bolt

1

24

45139

M12 Nyloc Nut

9

25

45140

M16 Nyloc Nut

15

26

45141

M20 Nyloc Nut

6

27

45167

M12 Zinc Plated Spring Washer

2

28

45292

7/16” x 1 1/2” Lynch Pin

2

29

45295

Cat 2 x 4 1/2” Clevis Pin

2

30

45436S

M12 x 45 Class 4.6 Zinc Plated Set Screw

8

31

45444

M12 x 90 Class 4.6 Zinc Plated Bolt    

(Refer Table for Quantities)

32

45458S

M16 x 40 Class 4.6 Zinc Plated Set Screw

14

33

45461

M16 x 55 Class 4.6 Zinc Plated Bolt

1

34

45506

M20 x 90 Class 4.6 Zinc Plated Bolt

4

35

45508

M20 x 110 Class 4.6 Zinc Plated Bolt

2

36

47237

7/8” UNF x 5 1/2” Zinc Plated High Tensile Bolt (2.5m Only)

1

37

47244

7/8” UNF x 6 1/2” Zinc Plated High Tensile Bolt

1

38

47548

7/8” UNF Nyloc Nut

1

920 Maxi-Till Cultivator  

Complete Assembly

Pt. No. 67202

Issue 1096

Part numbers for different width machines

Item

3.1m (10’) 30 Tine

3.6m (12’) 34 Tine

1

4920352

4920377

13

4920540

4920545

14

4920560

4920565

18

4920612

4920622

Summary of Contents for Maxi-Till 920





















Reviews: