manualshive.com logo in svg

Duncan Enviro 740, Owner'S Manual

Share
Download
Duncan Enviro 740 Owner'S Manual Download Page 21

19

Pt. No. 67304

Issue 1217

 Machine 

Row 

Sowing 

 

Size  Spacing 

Width (m)

 15 

Run

  

150 

2.25 

49 

197 

Hign

 17 

Run 

130 2.21 50 

200.5 

Speed

 15 

Run 

150 2.25 

30.5 

122.5 

Low

 17 

Run 

130 2.21 31 

125 

Speed

 19 

Run 

150 2.85 39 

155.5 

High 

 21 

Run 

135 2.84 39 

156 

Speed

 19 

Run 

150 2.85 24 97 

Low

 21 

Run 

135 2.84 

24.5 

97 

Speed

 23 

Run 

150 3.45 32 

128.5 

High 

 26 

Run 

130 3.38 32 

129 

Speed

 23 

Run 

150 3.45 20 80 

Low

 26 

Run 

130 3.38 20 80 

Speed

Number of Hand Crank Turns for Seed Rate Calibration

9 

Weigh the seed collected during the test in kilograms.

10 

Calculate the seed rate by multiplying the kgs previously 
collected x 40 (1/40th ha method) or x 10 (1/10th ha 
method) depending on requirement. If the resultant 
calculation does not produce the desired seed rate use 
the enclosed seed rate calculator disc to determine the 
correct gearbox setting. 

 Refer 

Use of Seed Rate Calculator 

P 20

.

 

Suggestion

 To be on the safe side and until confidence 

has been gained with the method of calibration it is advisable to 
conduct a second test at the newly determined gearbox setting.

11 

Where a coated seed is used it is advisable to check the 
calibration after 1 hectare as dressings can tend to create a 
coating on the seed metering wheels thus changing the the 
flowing properties of the seed which in turn alters the seed 
rate.

Calculating Number of Hand Crank Turns for
Other Working Widths

1

  For clutch output sprocket of 19 tooth and gearbox input 

sprocket of 15 tooth (standard 

High Speed

 

Setting

)...

      Constant = 0.443

2

  For clutch output sprocket of 15 tooth and gearbox input 

sprocket of 19 tooth.(

Low Speed Setting

)...

Constant = 0.276

Crank Turns =  

Area in Metre

2

  x Constant

    Working Width

For 1/40 Hectare (250 m

2

) Calibration

Seed Rate = Actual Seed Collected (kg) x 40

For 1/10 Hectare (1000 m

2

) Calibration

Seed Rate = Actual Seed Collected (kg) x 10

 Speed Setting

 Gearbox   Clutch 

  

Sprocket 

Sprocket

 

High Speed

 

15 Tooth  19 Tooth

 (Standard)

 

Low Speed

 19 

Tooth 

15 

Tooth

Turns for 

1 / 40

Hectare

Turns for 

1 / 10

Hectare

Speed Setting

(Refer Above)

fig 19

Summary of Contents for Enviro 740









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands