Dumas 1257 Manual Download Page 23

Page: 23 / 42

PT-212

Kit No. 1257

184

Cement a No. 4 Flat Washer centered on LC16.

185

Cement LC15/16 to the rear of the Torpedo Tube.

NOTE: make sure that one of the little corners is facing straight up. (See FIG 64)

186

Cut eight 1/4” long pieces from the 1/16” dia. x styrene rod.

187

Cement the 1/4” long styrene rods to the 1/4" wide paper band at the rear of the Torpedo Tube.

NOTE: Each styrene rod must line up with a small corner on LC15.

188

MANIFOLD:

Cut 1/4

” dia. wood dowel to the dimensions shown on the drawing.

(See FIG. 65)

189

Cement the two 1/4” dia. wood dowel pieces together.

190

Cement a small brass Eyelet centered to the end of the shorter piece.

191

Cut a 1/4" length from the 3/16” wood dowel supplied in the kit.

192

Carefully, drill a 3/64” dia, hole down the center of the 3/16” dia. dowel.

193

Cement the1/4" length of the 3/16” wood dowel to the top of the Torpedo Tube where shown on the
drawing.

(See FIG. 65)

194

Cut the stem of a large Pi

n down to 5/16”.

(See FIG. 65)

195

Cement the cut down Pin into the hole in the center of the 3/16” dia. wood dowel.

196

Place, DO NOT cement the Manifold on top of the Torpedo Tube, and mark the locations of the
adjacent bands found on the Torpedo Tube.

197

Cut the white adhesive backed paper into (3) -

1/16” wide, 2” long strips.

198

Wrap the paper strips around the wood dowel at the locations where you marked previously.

(See

FIG. 65)

199

Cement the Manifold to the top of the torpedo Tube. Yes, the Manifold will lay toward the side of
the Torpedo Tube.

NOTE: The small brass Eyelet at the end of the Manifold must touch the 3/16” dia. dowel when

seated properly.

200

Paint the Torpedo Tube GRAY, or your favorite color. (You see a pattern developing here?)

CREW HATCH (See FIG. 66)

201

Cut the Hatch Top and the Hatch Bottom form the 1mm PVC sheet provided in the kit.

NOTE: YOU will need to cut five (5) Hatch Tops and four (4) Hatch Bottoms from the 1mm PVC

sheet. You will need to cut the remaining one (1) Hatch Bottom from the 2mm PVC sheet.

202

Cement the Hatch Top centered on the Hatch Bottom.

203

HANDLE:

Bend 1/32” dia. brass wire to match the full size pattern found on the drawing

(See FIG.

66).

BUILDING TIP:

I used the very tip of my long nose pliers which seemed to work well. It was close enough

– no measuring was needed.

204

Drill two 1/32” dia. holes in the top of the Hatch Top, 1/8” away from the front edge, to match your
brass Handle.

Summary of Contents for 1257











































Search results

Summary of Contents for 1257

Reviews:

Related manuals for 1257

Brands by name

Popular brands

Dumas 1257, Manual

Search results

Summary of Contents for 1257

Reviews:

Related manuals for 1257

Brands by name

Popular brands