Dulas VC50SDD Installation & Technical Manual Download Page 42

Page: 42 / 46

VC50SDD Installation &

Technician’s Manual

Page 42 of 46

4. Refrigerator Installation and Commissioning

•

Make sure there is enough cable for the refrigerator to be moved for

maintenance and cleaning.

•

Ensure that the PV switch on the refrigerator is in the ‘OFF’ position.

•

Connect the cable to the refrigerator and turn the PV switch ‘ON’.

•

Very firmly secure the solar cable to the wall, ensuring that if it is pulled

it cannot strain the electrical connections.

•

Check the refrigerator compartment temperature display for operation.

Use a torch if natural light is insufficient.

•

Check the refrigerator cooling circuit is working (condensers should get

warm).

•

Allow the temperature to stabilise (this may take up to 7 days)

•

Check that the refrigerator compartment is +4



C to +6



5. F

inally…

STOP AND THINK

Have we done a good job?

Is it good quality?

•

Check that all cables are securely fixed and terminated

•

Complete the user training. Make sure the user understands:

How to get help,

How to operate the system,

How to do routine maintenance.

•

Tidy up the site making sure nothing is left behind.

•

Check that the installation record is complete and signed by the

responsible persons.

Signature of person responsible for installation ......................................................

Signature of person responsible for health centre ...................................................

Summary of Contents for VC50SDD















































Search results

Summary of Contents for VC50SDD

Reviews:

Related manuals for VC50SDD

Brands by name

Popular brands

Dulas VC50SDD, Installation & Technical Manual

Search results

Summary of Contents for VC50SDD

Reviews:

Related manuals for VC50SDD

Brands by name

Popular brands