Dukane Infinity 43NSLA Quick Start Manual Download Page 9

Page: 9 / 65

CTION 2 - H

EAL
TH
AND

AFET

Infinity™

Series Servo Ultrasonic Press Systems QUICK START GUIDE

Health and Safety

General Considerations

Safe Operation

Please observe these

health and safety recommendations

for safe, efficient,

and injury-free operation of your equipment.

Proper Installation

- Operate system components only after they are properly

installed.

No Unauthorized Modifications

- Do not modify your system in any

way unless authorized to do so by Dukane. Unauthorized modifications
could cause equipment damage and/or injury to the operator. In addition,
unauthorized modifications will void equipment warranty.

Keep the Cover On

- Do not remove any equipment covers unless directed

to do so by Dukane. Hazardous electrical voltages are present which could
cause injury.

Grounded Electrical Power

- Operate this equipment only with a grounded

electrical connection.

See Electrical Safety

for grounding instructions, Page 7.

Comply with Regulations

- you may be required to add accessories to bring

the system into compliance with applicable regulations (OSHA in the USA)
for machine guarding and noise exposure.

Use Eye Protection

- Wear ANSI approved safety impact goggles.

Acoustic Stack Hazard

- When an acoustic stack (transducer, booster, horn

and tip) is energized by the ultrasound signal, it presents a potential hazard.
Stay clear of an energized stack.

System Abort Switch

- Install a system abort switch at each operator station

when ultrasonic plastic assembly equipment is used with automatic material

handling equipment in an automated system.

Foot Switch

- Using a foot switch in place of the optical touch finger switches

(operate switches) violates OSHA regulations.

System Electrical Cabling

- Electrical power must be off when connecting or

disconnecting electrical cables.

NOTE

These recommendations apply to

the welding system. System in this

guide refers to a complete group

of components associated with the

welding of parts, also known as an

ultrasonic assembly system.

WARNING

Any fixture manufactured by a third

party must comply with all OSHA and

ANSI requirements. All fixtures must

be guarded as necessary. Dukane

does not assume any responsibility

or liability for fixtures manufactured

by the customer or any third party

manufacturer.

CAUTION

At some time you may be asked

to remove equipment covers by

the Dukane Aftermarket Service

Group personnel. Before doing so,

disconnect the system electrically

from the incoming line AC power,

including the generator and press.

WARNING

Never operate the generator with the

cover off. This is an unsafe practice

and may cause injury.

Summary of Contents for Infinity 43NSLA


































































Search results

Summary of Contents for Infinity 43NSLA

Reviews:

Related manuals for Infinity 43NSLA

Brands by name

Popular brands

Dukane Infinity 43NSLA, Quick Start Manual

Search results

Summary of Contents for Infinity 43NSLA

Reviews:

Related manuals for Infinity 43NSLA

Brands by name

Popular brands