background image

63

English

Appendices

Optoma Global Offices

For service or support please contact your local office.

USA

3178 Laurelview Ct.  

 888-289-6786

Fremont, CA 94538, USA  

 510-897-8601

www.optomausa.com 

 

[email protected]

Canada

3178 Laurelview Ct.  

 888-289-6786

Fremont, CA 94538, USA  

 510-897-8601

www.optomausa.com 

 

[email protected]

Latin America

3178 Laurelview Ct.  

 888-289-6786

Fremont, CA 94538, USA  

 510-897-8601

www.optomausa.com 

 

[email protected]

Europe

42 Caxton Way, The Watford Business Park 

Watford, Hertfordshire,  

WD18 8QZ, UK 

 +44 (0) 1923 691 800

www.optoma.eu  

 +44 (0) 1923 691 888

Service Tel : +44 (0)1923 691865 

 

[email protected]

Benelux BV

Randstad 22-123 

 +31 (0) 36 820 0253

1316 BW  Almere 

 +31 (0) 36 548 9052

The Netherlands 

www.optoma.nl  

France 

Bâtiment E   

 +33 1 41 46 12 20 

81-83 avenue Edouard Vaillant   

 +33 1 41 46 94 35

92100 Boulogne Billancourt, France  

 

[email protected]

Spain 

C/ José Hierro,36 Of. 1C   

 +34 91 499 06 06 

28522 Rivas VaciaMadrid, 

 +34 91 670 08 32

Spain  

Summary of Contents for ImagePro 8806



































































Reviews: