manualshive.com logo in svg

Duerkopp Adler 4181-3, Instructions For Service Manual, Page: 29 / 35

Share
Download
Duerkopp Adler 4181-3 Instructions For Service Manual Download Page 29

26

4.8 Setting the retaining spring of the hook thread

The retaining spring (1) holds the hook thread after having

performed the trimming. It is to be set in such a way that the

force necessary for pulling out the thread from the retaining

spring (1) is approximately equal to the force necessary for

pulling out the thread from the hook.

Caution! Danger of injury!

Switch off the main switch! Before starting the setting

operation, wait until the motor stops!

- Shape the retaining spring (1) in such a way that it fits close

with all  its surface (without wedge) onto the moving  trim-

ming knife (3).

- Shape the retaining spring in such a way that it fits close, with

the slightly tightened screw (2), onto the moving trimming

knife without any pressure.

- Tighten the screw (2), until the necessary force for pulling the

thread from the retaining spring is attained. The pulling force is

tested using a screwdriver (4) according to the illustration.

Caution!

The setting of the retaining spring (1) depends on

the setting of the hook tension and differs then

according to the respective sewing category.

The adjusting  screw  (2)  should  not be screwed in in such a

way that the retaining spring gets over the perimeter of the

moving trimming knife.

4.9 Setting switching of the electromagnets

The electromagnets of the trimming device and loosening of the

tensioner must work in accordance with the diagram. This is

ensured by setting the stopmotor (see the instructions for use of

the stopmotor).

1- 1. position of the needle (225

°

 on the handwheel)

2- 2. position of the needle (64

°

 on the handwheel)

3- position of stopping the tensioner (10

°

 ÷ 25

°

 on the hand-

wheel)

4- movement of the pickup roller

5- current of the trimming device electromagnet

6- current of the tensioner loosening electromagnet

5. Material trimming

5.1 Description of the trimming mechanism

The movement of the trimming knife is derived from its own

drive (motor) by means of eccentrics and of a  leverage with

the possibility of switching off the trimming function using

the lever (1) downwards, switching on is done by the lever (2)

in the direction  from the operator, the height setting is done

by the eccentric (3) using the pin 

  ø

 3 mm.

3

2

1

3

1

3

1

2

4

5

6

1

3

2

4

3

1

2

Summary of Contents for 4181-3




































Reviews:

No comments