A
B
C
D
E
F
G
H
L
M
N
P
Motore
Engine
sezione / section
N 4.5
85
749R
- M.Y. 2006 - edizione/edition 00
Revisione sede valvola
Controllare visivamente le sedi:
non devono presentare tracce
di vaiolature o incrinature.
Riscontrando lievi danni è possibile
eseguire una fresatura utilizzando le
apposite frese monotaglienti a
45°
e
60°
. Eseguire poi la smerigliatura
delle valvole e la verifica della tenuta.
In caso di danni eccessivi alle sedi
valvola è possibile eseguirne la
sostituzione utilizzando sedi
maggiorate di
0,03
e
0,06
mm,
sul diametro esterno, disponibili a
ricambio.
Importante
In caso di sostituzione delle
sedi, è necessario sostituire anche
i guidavalvola.
Operare come segue:
Rimuovere le sedi usurate fresandole
con cautela per non danneggiare
l'alloggiamento sulla testa.
Controllare il diametro degli
alloggiamenti sulla testa e scegliere la
sede valvola maggiorata più idonea,
considerando una interferenza di
montaggio di
0,04÷0,10
mm.
Scaldare lentamente ed
uniformemente la testa fino ad una
temperatura di
150 °
C e raffreddare
le nuove sedi con ghiaccio secco.
Piantare le sedi perfettamente in
quadro nel proprio alloggiamento
utilizzando gli appositi punzoni sedi
dei guidavalvole.
Lasciare raffreddare la testa e quindi
procedere alla lavorazione delle sedi
facendo riferimento alle seguenti
quote:
CA = Ø39,1±0,025
mm
CS = Ø31,6±0,025
mm
S = 1,205
mm
D = 0,7÷0,9
mm
Importante
Non usare pasta smeriglio
dopo la fresatura finale.
Overhauling the valve seat
Visually inspect valve seats:
they must be free from cracking or
pitting. Minor damage can be repaired
by milling with special
45°
and
60°
single-blade cutters. Grind valves and
run a leak test.
If valve seat is excessively damaged,
fit oversized seats. Replacement
seats are available with
0.03
and
0.06
mm oversized outer diameters.
Important
When you change the valve
seats, change the valve guides as
well.
Proceed as follows:
Remove the worn seats. Mill carefully
to avoid any damage to head bores.
Check diameter of head bores and
choose the oversized valve seat that
will give an interference fit of
0.04-
0.10
mm.
Heat the head gradually and evenly
up to
150 °
C and chill the new valve
seats in dry ice.
Drive the seats perfectly square into
the head bores using the appropriate
valve guide seat drifts.
Allow head to cool down and machine
seats to following dimensions:
CA = Ø39.1±0.025
mm
CS = Ø31.6±0.025
mm
S = 1.205
mm
D = 0.7 – 0.9
mm
Important
Do not use grinding paste
after final milling.
60 45
24±0.02
16±0.02
CA
D
S
S
D
CS
Summary of Contents for Superbike 749R 2006
