A
C
B
N
N
B
B
K
L
I
Tools Needed:
//
Allen Wrench – 5/32”
//
Drill
//
Straight Edge
//
Socket – 7/16”
//
5/16” &
7/16” Drill Bits
//
Hammer
//
Socket – 3/8”
//
Pliers
//
Nail or Sharp Punch
//
Phillips Screwdriver – #3
//
Marker or Pencil
//
Jack-Nut Friction Wrench
Installation Instructions:
The Tote may be placed on either side of the rear cargo area of the vehicle. It is recommended that the lid
open towards the outside of the vehicle for ease of access inside the Tote.
On the end of the Tote that will face the rear of the vehicle, attach one Stopper (I) to the Tote in
each corner with Bolt – 1/4” x 3/4” (J) and attach Lock Swivel (M) in desired corner, as pictured.
Attach the Base Plate (A) to each Channel (B) with two Screws – Flat Head 1/4” x 1/2” (C)
using an Allen Wrench – 5/32”. Insert the four Adjustable Feet (N) into the pre-drilled holes in
the bottom of each Channel (B).
Attach the Lock Latch (K) in the pre-drilled holes on the side of the Channel (B) with two Screws –
#8 x 5/16” (L) using the Phillips Screwdriver.
(Note: Make sure the location of the Lock Latch (K)
corresponds with the Lock Swivel (M) you attached to the Tote in Step 1.)
Place the Tote and Base Plate (A) with Channels (B) into the vehicle in desired location.
Slide the Tote into the Base Plate (A) with Channels (B) until the Stoppers (I) contact the Channels.
Note: Make sure the Lock Latch (K) and the Lock Swivel (M) are aligned and function properly.
Make sure the Tote is positioned properly and the rear door of the vehicle closes without contacting
the Tote. It is recommended to have at least 1“ clearance in between the Tote and the rear door.
Make marks at the location of the Base Plate (A), as pictured, using a marker or pencil. Hold the
bracket
fi
rmly in place and remove the Tote. Note: Back of bracket should be 3” from trim piece.
If you have a SUV that has a rear
fl
oor compartment, the bracket can be attached to the
removable
fl
oor panel.
If you do not have this compartment proceed to Step 7.
Continued on Page 2..
Before drilling see
‘Drill Warning’
on page 2.
Drill holes in the panel with a 5/16” drill bit in the
proper location
(between marks made in the slots in the base plate – determined in Step 5)
. Attach
bracket with two Bolt – Hex Head 1/4” x 2-1/2” (G), four Washers – Flat 1/4” (H), and two Nuts–
1/4” (E), as pictured, using Socket – 7/16” .
Tote Slide Bracket
Installation Instruction
DU-HA, Inc.
//
website: www.du-ha.com
//
phone: 1.866.306.DUHA (3842)
//
fax: 1.218.998.4013
//
306 Saint Andrews Street South, Fergus Falls, MN 56537
1
2
3
4
5
6
A
B
B
D
D
G
F
Option 2 —
Jack-Nuts
Option I —
Self Tapping Screws
H
I
J
J
I
K
L
N
C
M
N
N
N
Fits DU-HA Tote Part Number:
70103
Part Description
Qty
A
Base Plate
1
B
Channel
2
C
Screws – Flat Head 1/4” x 1/2”
4
D
Jack-Nut – 1/4”
2
E
Nut – 1/4”
2
F
Self Tapping Screws – 1/4” x 2-1/2”
2
G
Bolt – Hex Head 1/4” x 2-1/2”
2
H
Washers – Flat 1/4”
4
I
Stoppers
2
J
Bolt – 1/4” x 3/4”
2
K
Lock Latch
1
L
Screws – #8 x 5/16”
2
M
Lock Swivel
1
N
Adjustable Feet
4
70104
1
2
3
M
I
J
I
J
C
4
E
Not pictured.
Rear of Vehicle
Mark Locations
A
5
SUV
6
