Flip and slide the seats forward so you can gain access behind the seats.
Remove the Jack and Jack Tools. Set the DU-HA (A) in the truck behind the seats. The
notched area on the bottom of the DU-HA will fit around the Jack mount that is on the
floor. The hole on the drivers side should line up with the insert for the jack tools. You have
3 options for anchoring the DU-HA into your truck. Option 1 is to use a Self-Tapping Screw;
use this option if you want your DU-HA permanently attached in your truck. Option 2 is to
use a Jack-Nut; use this option if you want to be able to remove and re-install your DU-HA
in your truck. Option 3 is to use a thru-bolt; use this option for a more secure permanent
installation. Once you have the DU-HA in the desired position secure the DU-HA to the truck
using one of the three anchoring options. After installed re-install the Jack in the DU-HA.
Anchoring Option 1:
Self-Tapping Screw
Tools Needed:
//
Socket – 1/4”
//
Socket Wrench or Drill
Warning:
Before drilling into the truck floor make sure the area where you are going to drill
through is clear of any electrical wiring, fuel lines, tanks, and reservoirs. You will have
to look under the vehicle to make sure there are no obstructions at the hole locations.
Insert the Self-Tapping Screw (D) through a Washer – 1/4” (H) and the pre-drilled hole on
the passenger side in the bottom of the DU-HA and screw through the carpet or vinyl and
into the floor of the truck using a 1/4” Socket and Drill. DO NOT over-tighten. Secure the
drivers side using an M8 x 30mm bolt (K) and 1/4” washer (H) by threading into the insert
for the Jack Tools and tighten with a 13mm wrench.
Anchoring Option 2:
Jack-Nuts
Tools Needed:
//
Drill
//
Nail or Sharp Punch
//
Socket – 7/16”
//
7/16” Drill Bit
//
Hammer
//
Socket Wrench
//
Pliers
//
13mm Wrench
//
Phillips Screwdriver – #3
//
Jack-Nut Friction Wrench (supplied)
Warning:
Before drilling into the truck floor make sure the area where you are going to drill
through is clear of any electrical wiring, fuel lines, tanks, and reservoirs. You will have to
look under the vehicle to make sure there are no obstructions at the hole locations.
With the DU-HA set in your desired position, mark the hole in the bottom of the DU-HA on
the truck floor using a nail or sharp punch, on the passenger side only. Make sure the hole
on the drivers side lines up with the insert in the truck for the jack tools. You will need to
poke through the carpet and make a mark on the metal floor of the truck. Next remove
the DU-HA and pull back the carpet or vinyl flooring to expose the metal floor. Find the
previously made mark and drill a 7/16” hole.
Prior to installing the Jack-Nut–1/4” (E), hold the Jack-Nut with a pliers, and using the
phillips screwdriver, make a hole through the rubber on the Jack-Nut by pressing and
twisting into the rubber on the head of the Jack-Nut–1/4” (E). Next insert the Bolt Hex
Head – 1/4” x 2-1/2” (F) through the hole in the Jack-Nut Friction Wrench (J) and thread
all the way into the Jack-Nut–1/4” (E). Place the Jack-Nut–1/4” (E) in the drilled hole
(may
need a hammer to tap into hole)
. Secure the Jack-Nut to the vehicle by tightening the Bolt
Hex Head – 1/4” x 2-1/2” (F) using a Socket 7/16” and Socket Wrench, press firmly on the
Jack-Nut Friction Wrench (J) and tighten Jack-Nut – 1/4” (E) until you see the rubber on the
Jack-Nut starting to get squished. Do not over tighten (max torque = 41 in/lbs). Remove the
bolt from the Jack-Nut–1/4” (E).
Note:
Jack-Nut Friction Wrench is only used to install Jack-Nuts.
It does not take a lot of
torque to break a Jack-Nut so it is best to use a 7/16” Socket and Socket Wrench. If using
a drill with a 7/16” Socket, be very careful not to over tighten and strip out the Jack-Nut.
2017-20
20
Ford SuperDuty Regular Cab -
Behind-the-seat Storage
Installation Instructions:
Installation Instructions
DU-HA, Inc.
//
website: www.du-ha.com
//
phone: 1.866.306.DUHA (3842)
//
fax: 1.218.998.4013
//
306 Saint Andrews Street South, Fergus Falls, MN 56537
1
2
A
B
Fits DU-HA Part Number
20115
DIVIDER – 20115
1
2
3
4
B
3
Jack-Nut
B
B
4
D
K
H
H
2
