DTAR Wave-Length Installation Instructions Manual Download Page 15

15

www.dtar.com        |

Limited Warranty / Disposal Guidelines

D-TAR offers the original purchaser a one-year limited warranty on both labor 
and materials starting from the day this product is purchased from an authorized 
D-TAR Dealer or as original equipment in an instrument, provided that a qualified, 
professional repairperson or luthier performed the installation. D-TAR will repair 
or replace this product, at its option, if it fails due to faulty workmanship or 
materials during this period. Defective products should be returned to your USA 
dealer, international distributor, or sent direct to our factory postage prepaid 
along with dated proof of purchase (e.g., original store receipt) and a RMA 
number clearly written on the outside of the box. Please call our factory for 
issuance of an RMA number. 

This warranty does not apply to damage to this product or an instrument 
caused by misuse, mishandling, accident, abuse, alteration, faulty installation or 
installation by a non-qualified repairperson. 

Product appearance and normal wear and tear (worn pain, scratches, etc.) are not 
covered by this warranty. 

   

D-TAR reserves the right to be the sole arbiter as to the misuse or abuse of this 
product. D-TAR assumes no liability for any incidental or consequential damages, 
which may result from the failure of this product. Any warranties implied in fact or 
by law are limited to the duration of this express limited warranty.

This product must not be disposed of with your other household waste.  
Instead, it is your responsibility to dispose of your waste equipment by handing 
it over to a designated collection point for the recycling of waste electrical and 
electronic equipment. The separate collection and recycling of your waste  
equipment at the time of disposal will help to conserve natural resources and 
ensure that it is recycled in a manner that protects human health and the  
environment. For more information about where you can drop off your waste 
equipment for recycling, please contact your local city office, your household 
waste disposal service or the shop where you purchased this product.

Summary of Contents for Wave-Length

















Reviews: