SA1350/ DT135D
ENGLISH
2
3
ENGLISH
I/O Ports
Rear View
Front View
Powering ON and OFF
The Power Button is located in the front of the product. The Power Button may be configured
to function differently depending on the power options of the operating system. In general, to
turn on the product, push and release the Power Button on the front bezel. The adjacent power
LED will be lit (blue) and the corresponding interface will be displayed on the display monitor.
To turn off the device, again depending on software operating system, push and release the
Power Button or use a software shutdown interface. In the event of system lockup, the Power
Button may be used to perform a reset on the device. To do that, push and hold the Power
Button for at least 4 seconds. The system will shut down and all unsaved work may be lost.
Pushing on the Power Button again will restart the device.
NOTE:
The SA1350 is programmed to Power On automatically when power is first applied or
re-established.
Precautions
• Always exercise care when operating and handling.
• Never disassemble any portion of the enclosure. It will void any product warranty.
• Do not use any AC/DC adapter other than the one provided with the device or
acquired from the manufacturer or its partners.
• In the unlikely event that smoke, abnormal noise, or strange odor is present,
immediately power down the product and disconnect all power sources.
• Please report the problem to your device provider immediately.
A
B
C
D
E
F
G
H
Power button
USB 2.0 (4)
RS232 COM ports (2)
A
D
F
B
E
G
C
H
DC-in
DisplayPort
DVI-I port
Ethernet port
Audio jacks (2)
VESA Mounting Bracket Installation Guide
The product package includes a VESA-compliant mounting bracket (1) which mounts the
product (2) onto a VESA-compatible monitor or display.
NOTE
: The VESA Mounting Bracket is compatible with most displays and monitors that support
the VESA standard.
Step1:
Locate the existing mounting holes on the monitor.
•
Line the bracket holes up with the holes on the back of the
•
monitor, as shown to the right.
Place the screws to hold the mounting bracket in place and
•
tighten the screws (do not over-tighten).
Step2:
Remove the two M3 screws (3) originally on the product.
•
Place the product (2) on the bracket rail with the interface
•
ports side facing downwards so that the two mounting
holes on the appliance are aligned with the existing holes
on the rail (see picture).
Step 3:
Apply and tighten the screws into their original locations and make sure that the bracket and
•
the product are properly secured.
<1>
<2>
<3>
SA1350 Server Installation and Appliance Registration
Please refer to the corresponding User Guides for server software installation instructions.
After turning on the SA1350 for the first time, a screen prompt is displayed for registering the
appliance. If the screen prompt is not shown, please follow the instructions below:
Press and hold “
1.
Control
+
Shift
+
Space
” to exit the WCM
Player software.
Navigate to
2.
Start
|
All Programs
|
DT Research
|
WebDT
Signage Player
Select
3.
Register WebDT Signage Player
Again. The
Player
Registration
screen should appear. Fill in all fields to register.
The required information is marked.
Click
4.
OK
to register and connect to the WebDT Signage
Appliance Publish Server.
Device Ports
The product features an optimal set of I/O ports while preserving the compact size of the
system. The DisplayPort and DVI-I connectors, COM ports, Network (10/100/1000 BaseT
Ethernet), and Power ports are supplemented by a set of four USB 2.0 and two Audio ports.
Through its USB ports, the product supports a wide range of USB-based peripherals. These
peripherals are applicable in providing the means for software installation, application storage,
data storage, and system software recovery and updates.
